The RWB JK build

edzilla123 · 05-04-2016, 07:24 PM

Well thew front are cut and just tapped on for adjustments, the front bumper is now the biggest project on my hands

edzilla123 · 05-05-2016, 12:22 AM

the night was a success, the lines for the rear are lined up and ready to be cut on both sides, I will be cutting 18-20 mm down from the body line in the rear quarter panel

edzilla123 · 05-05-2016, 12:23 AM

Where the rear bumper attaches to the body i will be cutting around it to attempt to keep it as an attachment point

edzilla123 · 05-08-2016, 12:00 PM

Did a little project i have been procrastination for a while now. dual oil catch cans.

edzilla123 · 05-13-2016, 01:16 AM

For the DIY'ers out there the picture go in order of my cuts
Cut:1 i cut just bellow where the bumper meets the body to keep the mount for the bumper. as well the top most line was first cut do to the unknown as to where the body met the inner fender well

Cut 2: i cut an inch or so down just so i can look behind the body to determine where the body met the well.

Cut 3: i determined the perfect line to follow to cut was the width of electrical tape that is where you will eventually need to cut the well at.

Cut 4: not finished in the picture but right above the blue tape is where i will be cutting the well to finish the cutting.

Kingbaby · 05-13-2016, 04:13 AM

*tips hat*

Surely you have a DD and you don't quit on this...

Enjoyed the build however short, and I'm in for the finish!

Keep it up!

edzilla123 · 05-13-2016, 10:06 AM

Quote:

Originally Posted by Kingbaby

*tips hat*

Surely you have a DD and you don't quit on this...

Enjoyed the build however short, and I'm in for the finish!

Keep it up!

thanks ma dude and my DD is an 07' audi A3 bagged

edzilla123 · 05-21-2016, 01:03 PM

Wheels specs are final! 19x13 -25 and in front 19x10.5 -23! 7 inch lip in back with -2 degrees of camber

edzilla123 · 05-25-2016, 02:28 PM

So after contacting both bulletproof and aimgain about the front fitment issuse i have made no progress. they say all i need to do is go to a shop and have them doing it for you. they are stating that when making them they come out longer then they are supposed to. SO if you get the aimgain flares be prepared for this perfect fitment in front. not happy with this 2500 dollar "high quality" product.

madeinjapan · 01-19-2017, 07:43 AM

Quote:

Originally Posted by edzilla123

So after contacting both bulletproof and aimgain about the front fitment issuse i have made no progress. they say all i need to do is go to a shop and have them doing it for you. they are stating that when making them they come out longer then they are supposed to. SO if you get the aimgain flares be prepared for this perfect fitment in front. not happy with this 2500 dollar "high quality" product.

fiberglass mafia is looking better and better after seeing this

what a shame

Wiggins3377 · 05-25-2016, 03:53 PM

you could always buy the Aimgain bumper from me for one hell of a price and sell you current bumper to make up for it!!!!

In all seriousness, this is good info for any potential aimgain buyers out there.

Breadz · 05-29-2016, 06:52 PM

sick build man

edzilla123 · 05-31-2016, 10:31 AM

Quote:

Originally Posted by Breadz

sick build man

Much appreciated sir

edzilla123 · 06-19-2016, 09:58 AM

they say money dosnt bring happiness, well the money that made these mine sure did.

edzilla123 · 06-19-2016, 01:37 PM

if your a car guy i suggest this for your next purchase! first time using the quicklift

05-04-2016, 07:24 PM	#1 (permalink)
edzilla123 Enthusiast Member Join Date: Aug 2014 Location: Darien, IL Posts: 280 Drives: 09,370z, red Rep Power: 12	Well thew front are cut and just tapped on for adjustments, the front bumper is now the biggest project on my hands LMBmikeZ and astro932 like this.

05-05-2016, 12:22 AM	#2 (permalink)
edzilla123 Enthusiast Member Join Date: Aug 2014 Location: Darien, IL Posts: 280 Drives: 09,370z, red Rep Power: 12	the night was a success, the lines for the rear are lined up and ready to be cut on both sides, I will be cutting 18-20 mm down from the body line in the rear quarter panel LMBmikeZ, carlitos_370z and astro932 like this.

05-08-2016, 12:00 PM	#4 (permalink)
edzilla123 Enthusiast Member Join Date: Aug 2014 Location: Darien, IL Posts: 280 Drives: 09,370z, red Rep Power: 12	Did a little project i have been procrastination for a while now. dual oil catch cans. cv129 and DatsunFTW like this.

05-13-2016, 01:16 AM	#5 (permalink)
edzilla123 Enthusiast Member Join Date: Aug 2014 Location: Darien, IL Posts: 280 Drives: 09,370z, red Rep Power: 12	For the DIY'ers out there the picture go in order of my cuts Cut:1 i cut just bellow where the bumper meets the body to keep the mount for the bumper. as well the top most line was first cut do to the unknown as to where the body met the inner fender well Cut 2: i cut an inch or so down just so i can look behind the body to determine where the body met the well. Cut 3: i determined the perfect line to follow to cut was the width of electrical tape that is where you will eventually need to cut the well at. Cut 4: not finished in the picture but right above the blue tape is where i will be cutting the well to finish the cutting. LMBmikeZ likes this.

05-21-2016, 01:03 PM	#8 (permalink)
edzilla123 Enthusiast Member Join Date: Aug 2014 Location: Darien, IL Posts: 280 Drives: 09,370z, red Rep Power: 12	Wheels specs are final! 19x13 -25 and in front 19x10.5 -23! 7 inch lip in back with -2 degrees of camber LMBmikeZ and astro932 like this.

05-05-2016, 12:23 AM	#3 (permalink)
edzilla123 Enthusiast Member Join Date: Aug 2014 Location: Darien, IL Posts: 280 Drives: 09,370z, red Rep Power: 12	Where the rear bumper attaches to the body i will be cutting around it to attempt to keep it as an attachment point

05-25-2016, 02:28 PM	#9 (permalink)
edzilla123 Enthusiast Member Join Date: Aug 2014 Location: Darien, IL Posts: 280 Drives: 09,370z, red Rep Power: 12	So after contacting both bulletproof and aimgain about the front fitment issuse i have made no progress. they say all i need to do is go to a shop and have them doing it for you. they are stating that when making them they come out longer then they are supposed to. SO if you get the aimgain flares be prepared for this perfect fitment in front. not happy with this 2500 dollar "high quality" product.

05-25-2016, 03:53 PM	#11 (permalink)
Wiggins3377 A True Z Fanatic Join Date: Jul 2011 Location: Cincinnati Posts: 3,236 Drives: 40th 370 Rep Power: 78	you could always buy the Aimgain bumper from me for one hell of a price and sell you current bumper to make up for it!!!! In all seriousness, this is good info for any potential aimgain buyers out there. __________________ AccuAir/ AirRex/ Amuse/ Bride Japan/ Carbon Fiber Element/ Carbon Signal/ Evo-R/ NRG/ Project Kics/ Samco/ Shine Auto/ SPC/ SPL/ Stance/ Stillen/ Takata/ Top Secret/ Work

05-29-2016, 06:52 PM	#12 (permalink)
Breadz Base Member Join Date: Jan 2015 Location: Clovis Cali Posts: 240 Drives: 12 370z sport 6mt GM Rep Power: 11	sick build man __________________ Fast Intentions Non res CF, CF Duckbill, Stillen G3, Fujimura Diffuser, Swift Springs, 180 Headlights, Forgestar F14Bronze

06-19-2016, 09:58 AM	#14 (permalink)
edzilla123 Enthusiast Member Join Date: Aug 2014 Location: Darien, IL Posts: 280 Drives: 09,370z, red Rep Power: 12	they say money dosnt bring happiness, well the money that made these mine sure did. OTW Z-Boy likes this. Last edited by edzilla123; 06-20-2016 at 12:18 AM.

06-19-2016, 01:37 PM	#15 (permalink)
edzilla123 Enthusiast Member Join Date: Aug 2014 Location: Darien, IL Posts: 280 Drives: 09,370z, red Rep Power: 12	if your a car guy i suggest this for your next purchase! first time using the quicklift astro932 likes this.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
7at 4.08 build	Taylortoons	Member's 370Z Gallery	19	03-01-2017 08:44 PM
My Z Build	pwrhsms	Member's 370Z Gallery	43	09-09-2013 11:35 AM
Possible Nos build	triadz	Forced Induction	7	04-06-2012 10:30 AM
THE "Lets argue about Bullitt's build with out ruining Bullitt's build thread" THREAD	Reaper42	Forced Induction	14	01-22-2011 05:24 PM
Datsun Roadster 1600...To build or not to build	motoextreme	The Lounge (Off Topic)	66	02-13-2010 12:40 AM