Anyone here into firearms?

bullitt5897 · 08-20-2009, 12:48 PM

Quote:

Originally Posted by tvfreakazoid

i did email the seller and pof and they said it was residue from being anodized and wasn't cleaned properly. I just took it off and washed it with some h2o and it came off. Me happy now.
Now i have to see how well it shots and how accurate it will be.

Anyone know how to sight an ar?

Like Semtex and others have said if your adding a scope or red dot of some type it should be self explanatory. However, for Iron sights your going to need a front Iron sight key (optics planet has a few). If it is a troy battle sight ur gonna need to modify the front sight key.

The best way to sight the sights in is to start at 50 or 100yd (Id recommend 100yd).
1) Flip your sights up make sure your rear windage sights are centered.
2) Make sure the sights are tightly fastened to the rail (they due tend to come loose over time)
3) Use a Bipod or bench rest and get centered on your target at 100yds.
4) squeeze off a round (note. if you have poor trigger control you will be all over the place and wont be able to get a consistent zero)
5) Ok you now know where your first Point of Impact is. if its low then adjust your front sight one to two clicks lower. If high then raise it the same.
6) Remember you want to basically walk your shots to the bulls eye so little changes will give you a consistent movement across the target and you wont get lost.
7) If the POI is right then you must adjust the rear windage sight to the left to pull your shot back into the target.

The rest is up to you. Be safe and have fun with the POF you will enjoy it! I am hitting less than 1.5 MOA out to 700yds with my POF 6.8 16"...

Trust me you will love the gun

tvfreakazoid · 08-27-2009, 01:40 PM

I will give a try. Just need to find a area in Sactown, CA to shoot that far. I'm looking to get a MI iron sight then eventually a scope. They are so expensive. I may just a cheap one.

Quote:

Originally Posted by bullitt5897

Like Semtex and others have said if your adding a scope or red dot of some type it should be self explanatory. However, for Iron sights your going to need a front Iron sight key (optics planet has a few). If it is a troy battle sight ur gonna need to modify the front sight key.

The best way to sight the sights in is to start at 50 or 100yd (Id recommend 100yd).
1) Flip your sights up make sure your rear windage sights are centered.
2) Make sure the sights are tightly fastened to the rail (they due tend to come loose over time)
3) Use a Bipod or bench rest and get centered on your target at 100yds.
4) squeeze off a round (note. if you have poor trigger control you will be all over the place and wont be able to get a consistent zero)
5) Ok you now know where your first Point of Impact is. if its low then adjust your front sight one to two clicks lower. If high then raise it the same.
6) Remember you want to basically walk your shots to the bulls eye so little changes will give you a consistent movement across the target and you wont get lost.
7) If the POI is right then you must adjust the rear windage sight to the left to pull your shot back into the target.

The rest is up to you. Be safe and have fun with the POF you will enjoy it! I am hitting less than 1.5 MOA out to 700yds with my POF 6.8 16"...

Trust me you will love the gun

semtex · 08-27-2009, 01:51 PM

Quote:

Originally Posted by tvfreakazoid

I will give a try. Just need to find a area in Sactown, CA to shoot that far. I'm looking to get a MI iron sight then eventually a scope. They are so expensive. I may just a cheap one.

Yes, they are expensive. I can't disagree with you there. If you do decide to go that route, I recommend taking a look at laruetactical.com -- they have lots of optic/mount combos.