Any other Intakes other than Stillen and Injen?

TipsZ · 08-26-2009, 02:45 PM

Thanks Mod .. I completely understand. Very nice work by the way! I am looking for those lower numbers as well .. specifically under 3.5k RPM for that extra oompf. I was hoping that intakes similar to Stillen or Injen would help provide that lower spectrum increases.

Quote:

Originally Posted by Modshack

Yeah, I made it. Too labor intensive (and honestly I'm not real confident of the general DIY ability here on this forum) to offer as a kit. It is just an example of what can be done with a little imagination. Since I've custom tuned my aluminum MAF holders for a "0" fuel trim output it should dyno with the best of them though that's not what's important to me. The power under the curve is. Those that are going for the MAX dyno numbers are chasing gains you'll actually spend very little time using. Get some fresh air up there and your "in the engine bay" systems can run pretty cool with the right heat shielding. Mine runs only 6-10 degrees IAT above ambient. Similar to the one guy who posted IAT numbers on his Stillen..

jpit · 08-26-2009, 03:06 PM

I certainly agree with Modshack. The numbers that were just posted for the Stillen show the problem he is talking about. The intake loses power and torque from 1500 to about 3500 and really only starts to gain power above 6500. When Mike Kojima (a well-respected Nissan tuner) tested the Stillen G3 on an automatic the same problem was noted. Also, testing any intake with the hood open will skew the results one way or the other. With the hood open you are receiving air of a different temperature and getting it from a different location than you would when driving. Frankly, the only definitive idea I have taken from the intake threads is Modshack's Fang Vent which delivers the coolest air available to an intake mounted near the oem one. I have an RC2 on order and hope in combination the the MFV may provide some nice gains. However, even this might prove very difficult to test on a dyno.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Injen Intakes Installed! Pics, Vids, Dyno	m4a1mustang	Intake/Exhaust	177	07-28-2017 06:35 PM
Injen Dual Cold Air Intakes Nissan 370Z Z34 : INTENSEPOWER!	INTENSEPOWER	Exhaust/Intake	138	08-08-2011 01:34 PM
INJEN COLD AIR INTAKES now in stock at AMPLFIED	LOU@AMPLIFIED	Exhaust/Intake	30	11-02-2010 04:24 AM
370Z Injen Dual Intakes @ The 370ZSOURCE!!!!	Michael@TheZStore	Exhaust/Intake	30	10-14-2009 02:39 PM
To Stillen or Injen or AEM	jyhighsky	Intake/Exhaust	10	08-10-2009 10:18 AM

08-26-2009, 03:06 PM	#2 (permalink)
jpit Enthusiast Member Join Date: Feb 2009 Location: Washington State Posts: 440 Drives: 370Z Tour MT w/Spt Rep Power: 17	I certainly agree with Modshack. The numbers that were just posted for the Stillen show the problem he is talking about. The intake loses power and torque from 1500 to about 3500 and really only starts to gain power above 6500. When Mike Kojima (a well-respected Nissan tuner) tested the Stillen G3 on an automatic the same problem was noted. Also, testing any intake with the hood open will skew the results one way or the other. With the hood open you are receiving air of a different temperature and getting it from a different location than you would when driving. Frankly, the only definitive idea I have taken from the intake threads is Modshack's Fang Vent which delivers the coolest air available to an intake mounted near the oem one. I have an RC2 on order and hope in combination the the MFV may provide some nice gains. However, even this might prove very difficult to test on a dyno.