Post FI HFCs Install/ SES or CEL Help!!

eastwest2300 · 01-01-2013, 03:18 PM

Yup thats a fact.

eastwest2300 · 01-01-2013, 03:19 PM

We did start on the passenger side first, when we started to try to remove the demon bolt.

MJB · 01-01-2013, 03:19 PM

Ok, on the heat shield to each manifold, its has this white, padding like material attached to it, I guess like a heat resistant type padding.... anyways, it looks like whoever installed the manifold sensors got some of that padding caught up in the threads... Thats the only guess I could make... I had headers installed recently so I have the heat shields off.. check out the pic

MyKindaGuise · 01-01-2013, 03:22 PM

Quote:

Originally Posted by MJB

Ok, on the heat shield to each manifold, its has this white, padding like material attached to it, I guess like a heat resistant type padding.... anyways, it looks like whoever installed the manifold sensors got some of that padding caught up in the threads... Thats the only guess I could make... I had headers installed recently so I have the heat shields off.. check out the pic

He only has 5k miles on his car. It could've came from the delear like that and perhaps it just took a while for this to rear its ugly head.

eastwest2300 · 01-01-2013, 03:23 PM

I mean its possible, would this cause a code? We're wondering how long has this white sh!t been there, literally as I was removing the parts you told me to remove, i started looking for the actual o2 sensor.. And this is when I noticed the white stuff. Its only been a week and half since the HFC install.

MJB · 01-01-2013, 03:23 PM

And that padding might just be sticking out of the heat shield... I sort of thought it could be wrapped around the threads of the sensor when it was installed but you won't really know till you go and try to remove it.

Were you able to check out the wiring harness for any damage?

MyKindaGuise · 01-01-2013, 03:26 PM

Quote:

Originally Posted by MJB

And that padding might just be sticking out of the heat shield... I sort of thought it could be wrapped around the threads of the sensor when it was installed but you won't really know till you go and try to remove it.

That's what I said. I think best case would be to unplug and clean up that padding and then reseat the afr sensor and see if it clears the code. I don't see how any of that should even be there unless it was done upon original assembly of the header.

eastwest2300 · 01-01-2013, 03:26 PM

I looked at the Driver's side, and that side looked fine. I guess once I get the new o2 sensor, we'll find out. But you do notice both CEL codes are on the Passenger side. This has got to be issue, but what we're wondering is, is this white sh!t the stuff thats causing the error code.

eastwest2300 · 01-01-2013, 03:28 PM

Quote:

Originally Posted by MJB

And that padding might just be sticking out of the heat shield... I sort of thought it could be wrapped around the threads of the sensor when it was installed but you won't really know till you go and try to remove it.

Were you able to check out the wiring harness for any damage?

Not yet brother, its really cold out, and I didnt want to remove the air tubes, and leave the car without the air tubes connected, waiting on the new o2 sensor to come in the mail.

MJB · 01-01-2013, 03:37 PM

I don't think that padding could cause the CEL unless it was actually in the hole that the 02 threads into. But since you said nobody has removed it then I'm sure its just sticking out of the heat shield, take a look at my manifold. I pulled some of the padding threw like on yours.

eastwest2300 · 01-01-2013, 03:55 PM

No sh!t, ok soo I went out, used my long extension and pushed all that white stuff away, some fell on the ground I picked it, it was really soft, kinda like cotton or cotton candy, it was definitely wrapped around the entire base of the o2 sensor.

I also got my hand on the wiring harness clip on the opposite end, oh boy its gonna be a pain in the azz getting that off, luckily I have fairly small hands. Hopefully it'll be easier once i pull the air tube off.

eastwest2300 · 01-01-2013, 03:56 PM

Let me clarify, I didnt get ALL the white stuff off, but I got a large majority of it off.

MyKindaGuise · 01-01-2013, 03:57 PM

Quote:

Originally Posted by eastwest2300

No sh!t, ok soo I went out, used my long extension and pushed all that white stuff away, some fell on the ground I picked it, it was really soft, kinda like cotton, it was definitely wrapped around the entire base of the o2 sensor.

I also got my hand on the wiring harness clip on the opposite end, oh boy its gonna be a pain in the azz getting that off, luckily I have fairly small hands. Hopefully it'll be easier once i pull the air tube off.

You have your moms hands hahahaa jk but seriously. Clean that junk off make sure nothing is in the bung and then reinstall the sensor. Then do a battery pull for 10minutes then start the car and see if the CEL comes back

eastwest2300 · 01-01-2013, 03:59 PM

Quote:

Originally Posted by MyKindaGuise

You have your moms hands hahahaa jk but seriously. Clean that junk off make sure nothing is in the bung and then reinstall the sensor. Then do a battery pull for 10minutes then start the car and see if the CEL comes back

Ok so you're saying just clean it off, what should I use, I could probably use what, a tooth brush? Pull the battery, for 10 minutes. See if the code clears?

eastwest2300 · 01-01-2013, 04:00 PM

I have steel wool in both bungs, I was told it was a good idea to have it in there, it helps prevent codes.

01-01-2013, 03:18 PM	#91 (permalink)
eastwest2300 A True Z Fanatic Join Date: May 2010 Location: South FL Posts: 90,839 Drives: '16QX70/'21 Supra3.0 Rep Power: 2684550	Yup thats a fact. __________________ Infiniti QX70 & Toyota Supra 3.0 Premium

01-01-2013, 03:19 PM	#92 (permalink)
eastwest2300 A True Z Fanatic Join Date: May 2010 Location: South FL Posts: 90,839 Drives: '16QX70/'21 Supra3.0 Rep Power: 2684550	We did start on the passenger side first, when we started to try to remove the demon bolt. __________________ Infiniti QX70 & Toyota Supra 3.0 Premium

01-01-2013, 03:23 PM	#95 (permalink)
eastwest2300 A True Z Fanatic Join Date: May 2010 Location: South FL Posts: 90,839 Drives: '16QX70/'21 Supra3.0 Rep Power: 2684550	I mean its possible, would this cause a code? We're wondering how long has this white sh!t been there, literally as I was removing the parts you told me to remove, i started looking for the actual o2 sensor.. And this is when I noticed the white stuff. Its only been a week and half since the HFC install. __________________ Infiniti QX70 & Toyota Supra 3.0 Premium

01-01-2013, 03:23 PM	#96 (permalink)
MJB A True Z Fanatic Join Date: Aug 2011 Location: Tacoma, WA Age: 40 Posts: 1,498 Drives: a POS truck Rep Power: 495	And that padding might just be sticking out of the heat shield... I sort of thought it could be wrapped around the threads of the sensor when it was installed but you won't really know till you go and try to remove it. Were you able to check out the wiring harness for any damage? __________________ 09 Nismo #0483 sold. Viper or C7 next time around.

01-01-2013, 03:26 PM	#98 (permalink)
eastwest2300 A True Z Fanatic Join Date: May 2010 Location: South FL Posts: 90,839 Drives: '16QX70/'21 Supra3.0 Rep Power: 2684550	I looked at the Driver's side, and that side looked fine. I guess once I get the new o2 sensor, we'll find out. But you do notice both CEL codes are on the Passenger side. This has got to be issue, but what we're wondering is, is this white sh!t the stuff thats causing the error code. __________________ Infiniti QX70 & Toyota Supra 3.0 Premium Last edited by eastwest2300; 01-01-2013 at 03:57 PM.

01-01-2013, 03:55 PM	#101 (permalink)
eastwest2300 A True Z Fanatic Join Date: May 2010 Location: South FL Posts: 90,839 Drives: '16QX70/'21 Supra3.0 Rep Power: 2684550	No sh!t, ok soo I went out, used my long extension and pushed all that white stuff away, some fell on the ground I picked it, it was really soft, kinda like cotton or cotton candy, it was definitely wrapped around the entire base of the o2 sensor. I also got my hand on the wiring harness clip on the opposite end, oh boy its gonna be a pain in the azz getting that off, luckily I have fairly small hands. Hopefully it'll be easier once i pull the air tube off. __________________ Infiniti QX70 & Toyota Supra 3.0 Premium

01-01-2013, 03:56 PM	#102 (permalink)
eastwest2300 A True Z Fanatic Join Date: May 2010 Location: South FL Posts: 90,839 Drives: '16QX70/'21 Supra3.0 Rep Power: 2684550	Let me clarify, I didnt get ALL the white stuff off, but I got a large majority of it off. __________________ Infiniti QX70 & Toyota Supra 3.0 Premium

01-01-2013, 04:00 PM	#105 (permalink)
eastwest2300 A True Z Fanatic Join Date: May 2010 Location: South FL Posts: 90,839 Drives: '16QX70/'21 Supra3.0 Rep Power: 2684550	I have steel wool in both bungs, I was told it was a good idea to have it in there, it helps prevent codes. __________________ Infiniti QX70 & Toyota Supra 3.0 Premium

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
External Wastegates Post Install - Possible?	DIGItonium	Forced Induction	7	05-25-2012 01:53 PM
Z1 post MAF hose install problem	USAFZDRIVER	Intake/Exhaust	16	05-03-2012 03:21 AM
Asap help with aftermarket install post	Carbon_z	Audio & Video	5	11-01-2010 08:25 PM
shop or person to install HFCs in NY?	toxik	North East Region	11	05-16-2010 05:49 PM
Stillen Headers + Berk HFCs self-install report	wstar	Intake/Exhaust	84	04-14-2009 12:09 PM