My new HPS post MAF tubes installed

Bodytechz · 04-27-2011, 11:08 AM

Quote:

Originally Posted by Boost_lee

I trimmed my passenger side tube a little bit where the breather hose connects. Fit a little better after that

Pelican170 · 04-28-2011, 08:19 AM

Ok, finally got the tube to sit correctly. I had to twist the passenger side tube more to the left, so the HPS logo is facing almost to the left side. This made the Crank Case tube sit better and wasnt pressing in on the HPS tube itself....

waaaasabi · 04-29-2011, 02:48 PM

Quote:

Originally Posted by Pelican170

Ok, finally got the tube to sit correctly. I had to twist the passenger side tube more to the left, so the HPS logo is facing almost to the left side. This made the Crank Case tube sit better and wasnt pressing in on the HPS tube itself....

Hey can you take a pic of your setup? I had to rotate my passenger side tube as well, and even though the massive choke-kink is gone and it sits much better, it's still slightly 'deformed' in its shape...

Pelican170 · 05-02-2011, 09:21 AM

Quote:

Originally Posted by waaaasabi

Hey can you take a pic of your setup? I had to rotate my passenger side tube as well, and even though the massive choke-kink is gone and it sits much better, it's still slightly 'deformed' in its shape...

Yea, ill take a pic tonight when I get home.

Pelican170 · 05-04-2011, 11:49 AM

Quote:

Originally Posted by waaaasabi

Hey can you take a pic of your setup? I had to rotate my passenger side tube as well, and even though the massive choke-kink is gone and it sits much better, it's still slightly 'deformed' in its shape...

Hey sorry i havent had a chance to take that pic yet. Did you get it on? if you look at the pics in this thread, you can see how it should sit. The Crank Case hose part almost faces upward, compared to facing to the side on the drivers side, and the HPS logo will face leftward or far left compared to the drivers side which sits facing up. Ill take the pic tonight...

waaaasabi · 05-04-2011, 12:17 PM

Quote:

Originally Posted by Pelican170

Hey sorry i havent had a chance to take that pic yet. Did you get it on? if you look at the pics in this thread, you can see how it should sit. The Crank Case hose part almost faces upward, compared to facing to the side on the drivers side, and the HPS logo will face leftward or far left compared to the drivers side which sits facing up. Ill take the pic tonight...

Yeah I messed around with it a bit more, and my passenger side tube's logo is facing kinda left-middle. Diametrically speaking, the tube isn't exactly O-shaped like my driver side though; there's no major kink/bend in it anymore, but it's still not as perfectly formed as the driver side. I don't think it is so severe that it affects the amount of air going into the engine, per se, but was wondering it you were able to get it to sit in a position that allowed the tube to retain the ideal O-shape.

Pelican170 · 05-05-2011, 02:08 PM

Quote:

Originally Posted by waaaasabi

Yeah I messed around with it a bit more, and my passenger side tube's logo is facing kinda left-middle. Diametrically speaking, the tube isn't exactly O-shaped like my driver side though; there's no major kink/bend in it anymore, but it's still not as perfectly formed as the driver side. I don't think it is so severe that it affects the amount of air going into the engine, per se, but was wondering it you were able to get it to sit in a position that allowed the tube to retain the ideal O-shape.

yea again, sorry I havent posted any pics, very busy week for me. Although, I am not sure I can even get a good shot of it... Where isnt it "O" shaped? the only spot on mine that i thought might be very slightly off, was above the breather tube where the curve is to the throttle body. i think it may be sitting slightly "oval", but very slightly. Im pretty anal when it comes to stuff like this and I was happy with the way it was sitting when i decided I was done. That tube is a royal pain in the a** to get to sit right. im wondering how many others may have had this issue and just left it...

waaaasabi · 05-05-2011, 02:39 PM

Quote:

Originally Posted by Pelican170

yea again, sorry I havent posted any pics, very busy week for me. Although, I am not sure I can even get a good shot of it... Where isnt it "O" shaped? the only spot on mine that i thought might be very slightly off, was above the breather tube where the curve is to the throttle body. i think it may be sitting slightly "oval", but very slightly. Im pretty anal when it comes to stuff like this and I was happy with the way it was sitting when i decided I was done. That tube is a royal pain in the a** to get to sit right. im wondering how many others may have had this issue and just left it...

It's all good man, this week has been pretty hectic for me as well. As for the tube, yeah, it's pretty much that part between the throttle-body opening and the breather tube - mine is kinda oval-ish, too. It's not severe or anything, but was just wondering if you (and others) had a similar situation with the install and positioning - thanks for confirming the shape of your passenger side tube man

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
COBB Tuning Post MAF Tubes	hfrog355	Exhaust/Intake	1	03-03-2011 04:37 PM
FS: Cobb Post-MAF intake tubes (Black)	ArtVandaleigh	Parts for sale (Private Classifieds)	4	10-04-2010 10:14 PM
WTB: COBB post-Maf tubes - Black	kielbasa16	Parts for sale (Private Classifieds)	10	07-29-2010 09:05 AM
FS: Cobb Black Silicone Post-MAF Tubes	'10Anamoly	Parts for sale (Private Classifieds)	21	07-16-2010 07:39 AM

04-28-2011, 08:19 AM	#2 (permalink)
Pelican170 Track Member Join Date: Jul 2010 Location: Sandy Hook, CT Posts: 972 Drives: Nissan 370z Nismo Rep Power: 17	Ok, finally got the tube to sit correctly. I had to twist the passenger side tube more to the left, so the HPS logo is facing almost to the left side. This made the Crank Case tube sit better and wasnt pressing in on the HPS tube itself....