Just installed my Berk HFC's, SES Light blinking. Indicating misfire??

rsximus · 04-03-2010, 05:33 PM

Quote:

Originally Posted by Cyberium

As long as everything is nice and tight the gasket wouldn't be the issue. I would check your sensors again and make sure everything is where they should be and check to make sure everything is nice and snug under your car.

The flashing SES light usually indicates a cylinder misfire but that seems very unlikely in this situation. It doesn't even make any sense.

Yeah both 02 sensors are good. I was very careful when handling them.

The only other thing I did was remove the driver side airbox completely, I'll double check that side to see if everything is intact. Thanks for the suggestions Cyberium

Zsteve · 04-07-2010, 03:49 PM

Quote:

Originally Posted by rsximus

Yeah both 02 sensors are good. I was very careful when handling them.

The only other thing I did was remove the driver side airbox completely, I'll double check that side to see if everything is intact. Thanks for the suggestions Cyberium

Did you remove anything that deals with the steering sensor? I have the same lights and the guy did remove some piece that is part of the steering sensor or whatever and now I have to get the sensor reset by Nissan and thier diag device. I tried the battery thing a few times and that didnt work. Looks like anytime you remove a sensor you should have the battery disconnected.

rsximus · 04-07-2010, 07:43 PM

Quote:

Originally Posted by Zsteve

Did you remove anything that deals with the steering sensor? I have the same lights and the guy did remove some piece that is part of the steering sensor or whatever and now I have to get the sensor reset by Nissan and thier diag device. I tried the battery thing a few times and that didnt work. Looks like anytime you remove a sensor you should have the battery disconnected.

Zsteve, I was able to do the install without messing with the steering shaft or sensors. I know it's tight on the driver side but you can put a socket in there without disconnecting it. Same thing with my BMW 335i, when I replaced my steering wheel with an upgraded M-tech unit, I made sure to disconnect the battery and not mess with the steering position, it will throw it off the steering angle sensor and you'll get the VSC error ect. like many people have had.

Anyways, the problem is fixed now. I just had to disconnect the battery and reset the ECU again and all lights went away.

Going on 4 days and 400 miles now with no CEL/SES light.

Zsteve · 04-07-2010, 09:01 PM

Quote:

Originally Posted by rsximus

Zsteve, I was able to do the install without messing with the steering shaft or sensors. I know it's tight on the driver side but you can put a socket in there without disconnecting it. Same thing with my BMW 335i, when I replaced my steering wheel with an upgraded M-tech unit, I made sure to disconnect the battery and not mess with the steering position, it will throw it off the steering angle sensor and you'll get the VSC error ect. like many people have had.

Anyways, the problem is fixed now. I just had to disconnect the battery and reset the ECU again and all lights went away.

Going on 4 days and 400 miles now with no CEL/SES light.

good to hear, I gotta go see Nissan to get mine done (on their dime), hope they guy didnt mess something up.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Berk HFC's!	CrownR426	Wanted	0	03-10-2010 08:57 PM
FS: Berk HFC's	SOLISIMO	Parts for sale (Private Classifieds)	8	01-08-2010 01:33 PM
Installed Berk HFC's, car is going crazy... help!	Red370	Nissan 370Z General Discussions	9	10-07-2009 09:15 PM
WTB: Berk/Stillen/FI HFC's	Red370	Parts for sale (Private Classifieds)	3	10-02-2009 05:36 PM