Fast Intentions Long Tube Headers are here!

Zsteve · 12-18-2009, 03:50 PM

Quote:

Originally Posted by phelan

Correct me if I'm wrong (I'm terrible with exhaust systems apparently), but I mean that installing the LTH would also replace the HFCs. If we bought your HFCs already, do you offer any other discount?

The LTH would only give about another 6 hp if you already have the CBE and HFCs if Im reading everything right. And if you have the test pipes you are only getting about 3 more hp. Now are the SCs that are coming out going to be able to fit to these?

kannibul · 12-18-2009, 03:59 PM

Quote:

Originally Posted by Zsteve

The LTH would only give about another 6 hp if you already have the CBE and HFCs if Im reading everything right. And if you have the test pipes you are only getting about 3 more hp. Now are the SCs that are coming out going to be able to fit to these?

My thought is that the SC's that come out, maybe they will, maybe they won't - either way I'll probably go this direction first...until I can find out with reasonable certainty, at what RWHP the 7AT pops...

LTH's, Catback, G3...those aren't too terribly higher HP/Torque. If I read it correctly, that's only 20ftlb more torque between stock and full exhaust (I say only from the transmission standpoint, 30-RWHP/20-FTLB is nothing to laugh at)

F.I. Inc. · 12-18-2009, 03:59 PM

Daishi #003, thank you...

Tony

semtex · 12-18-2009, 04:00 PM

Quote:

Originally Posted by Zsteve

The LTH would only give about another 6 hp if you already have the CBE and HFCs if Im reading everything right. And if you have the test pipes you are only getting about 3 more hp. Now are the SCs that are coming out going to be able to fit to these?

Don't neglect the torque gains though. I mean, if you think about it, what Tony and his team have accomplished is quite remarkable. Compared to a setup with stock manifolds and HFCs, they're reducing backpressure. Usually, when you reduce backpressure, you lose some low-end torque as a tradeoff for gains higher up the rpm range. If you're lucky, you don't lose much or maybe even none at all. These guys managed to GAIN low-end torque! For me, it's a no-brainer to toss the Stillen headers I already have and switch over to these, because I lost torque with the Stillens. That, and they don't even line things up with their own CBE right. Stillen headers = FAIL as far as I'm concerned.

F.I. Inc. · 12-18-2009, 04:07 PM

Quote:

Originally Posted by Zsteve

The LTH would only give about another 6 hp if you already have the CBE and HFCs if I'm reading everything right. And if you have the test pipes you are only getting about 3 more hp. Now are the SCs that are coming out going to be able to fit to these?

No, if you look at the curve in some places we picked up over 12 and the same for torque. Peak was about 8 but the curve is much more important than peak power. Look at the consistency, look at how much sooner and higher the power and torque come on. This is achieved because of the headers. Believe me you can feel it driving. At the end of the day that is very important as well.

The RTP's made decent power and we saw a spike of 310 RWH SAE at the top but overall through the curve, they were very close to the HFC's. No doubt the Headers will out perform the RTP's and with a tune and CAI even more. In a supercharged application it is not even comparable. The headers will decimate all!

puckshaw · 12-18-2009, 04:09 PM

Quote:

Originally Posted by Kastley85891

^get an E85 tune lol - is NC inspection visual? or a CEL check sorta deal

Both

and sniffer test.

IvoryG · 12-18-2009, 04:21 PM

PM sent. Put me on the list.

SOLISIMO · 12-18-2009, 04:30 PM

Quote:

Originally Posted by IvoryG

PM sent. Put me on the list.

baller

jmlenz · 12-18-2009, 04:31 PM

Is it just me or did the OP originally say once the dies came to mandrel bend most the tubes the price would be a few hundred cheaper but that would take about 10weeks? I went back and tried to find it but couldn't. Am I trippin?

Quote:

Originally Posted by kannibul

Is the price coming down once you get the dies?

Will the discount still apply then?

Also, how much for ceramic-coated?

vipor · 12-18-2009, 04:34 PM

Quote:

Originally Posted by F.I. Inc.

The RTP's made decent power and we saw a spike of 310 RWH SAE at the top but overall through the curve, they were very close to the HFC's. No doubt the Headers will out perform the RTP's and with a tune and CAI even more. In a supercharged application it is not even comparable. The headers will decimate all!

kannibul · 12-18-2009, 04:59 PM

Quote:

Originally Posted by jmlenz

Is it just me or did the OP originally say once the dies came to mandrel bend most the tubes the price would be a few hundred cheaper but that would take about 10weeks? I went back and tried to find it but couldn't. Am I trippin?

That's what I thought too, but that's also why I posted the question!

F.I. Inc. · 12-18-2009, 05:31 PM

Quote:

Originally Posted by jmlenz

Is it just me or did the OP originally say once the dies came to mandrel bend most the tubes the price would be a few hundred cheaper but that would take about 10weeks? I went back and tried to find it but couldn't. Am I trippin?

We were originally going to sell the headers for $1,300-$1,400 if we were going to have to build them in many pieces. But, we want to get them out there for a reasonable price that is affordable. So we feel $995 is a great intro price and for previous customers $895.00 is even better.

G37Sam · 12-18-2009, 05:32 PM

PM sent Tony

Lostlife656 · 12-18-2009, 05:45 PM

Shouldn't have picked up those test pipes from you last week. Didn't know these were coming out. Ha may have to sell the pipes and get the lth in feb.

vipor · 12-18-2009, 05:47 PM

just get the lth, throw away the pipes lol.

/me starts saving 900$ very slowly

12-18-2009, 03:59 PM	#93 (permalink)
F.I. Inc. The370Z.com Sponsor Join Date: Feb 2009 Location: Simi Valley, CA Posts: 2,989 Drives: 2010 GT-R/2007 F-250 Rep Power: 685	*Daishi #003, thank you...* Tony __________________ *Follow us on Facebook: Fast Intentions Inc.* Phone: (805) 522-FAST (3278) Email: tony@fastintentions.com www.fastintentions.com "FUELED BY PASSION"

12-18-2009, 05:32 PM	#103 (permalink)
G37Sam A True Z Fanatic Join Date: Dec 2008 Location: Dubai, UAE Posts: 1,507 Drives: RB'd G37 Rep Power: 20	PM sent Tony __________________ '14 Viper GTS '08 RB'd G37S - Sold

12-18-2009, 05:47 PM	#105 (permalink)
vipor A True Z Fanatic Join Date: Aug 2009 Location: Euless, TX [ DFW ] Age: 41 Posts: 13,531 Drives: Nismo 09-0183 QAB Rep Power: 48	just get the lth, throw away the pipes lol. /me starts saving 900$ very slowly __________________ 2009 NISMO # 0193 \| QAB \| Albums! \| 05.04.10 (Dynojet) 291.94hp/248.28tq Oil Cooler (DIY) \| Custom Headlights \| GTSPEC Braces \| F.I. Long Tube Headers

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Stillen Gen III Ultra Long Tube Intakes Nissan 370Z FREE SHIPPING : IntensePOWER!	INTENSEPOWER	Exhaust/Intake	206	08-27-2010 02:41 PM
FS: Fast Intentions HFC's - Like New	Sonic370Z	Parts for sale (Private Classifieds)	8	10-01-2009 10:59 AM
New You Tube Video of Fast Intentions CBE 18" Resonators in CF	Aus370z	Australia/New Zealand	1	09-03-2009 11:57 PM
Stillen CBE vs Fast Intentions CBE?????	john370z	Intake/Exhaust	10	08-02-2009 09:12 PM
STILLEN G3 Ultra Long Tube Intake	nogoodname	Intake/Exhaust	117	03-17-2009 11:25 PM

12-18-2009, 04:21 PM	#97 (permalink)
IvoryG Base Member Join Date: Sep 2009 Location: Delaware Posts: 32 Drives: 08 Infiniti G37S Rep Power: 15	PM sent. Put me on the list.

12-18-2009, 05:45 PM	#104 (permalink)
Lostlife656 Base Member Join Date: Oct 2009 Location: Encinitas Posts: 14 Drives: 09 Nismo 370z #270 Rep Power: 15	Shouldn't have picked up those test pipes from you last week. Didn't know these were coming out. Ha may have to sell the pipes and get the lth in feb.