Forced Induction & 7AT 370z Info

FrankEtier · 07-14-2023, 08:43 AM

Quote:

Originally Posted by DarkJak

What did you use to adapt the 6an lines to the transmission? I had a small leak using rubber hose and clamps and I'm thinking about using leftover 6an from my fuel line work.

I used the fittings I purchased from Godzilla Race Works. I supplied the hose, cooler core, and other fittings. They have a full kit now though.

https://www.godzillaraceworks.com/37...0z-g37-q50-q60

Tractionless · 07-16-2023, 09:35 AM

Quote:

Originally Posted by FrankEtier

I have a 25 row cooler that bypasses the stock cooler and uses -6AN lines all the way back to the transmission. So far this summer I have not seen over 175 degrees in any situation while driving the car and it's hot in DFW Texas.

Nice, I'm NA with only spirited street driving and using the same Hayden core Z1 uses in their kit (purchased elsewhere), rubber lines with oetiker stepless and ABA Awab clamps which are stronger and provide for a better seal than T-bolts and without leaks.

I'm bypassing the OE "cooler" as my current summer trans. temps. are 122*-172* via gauge in the hot line coming from the trans.; therefore, the aftermarket cooler would be fighting the OE cooler heating the fluid to whatever my coolant temp is, typically 175-190* (170* stat.) which is obviously counterproductive.

Be careful not to cool under 122* as OE torque converter lockup is 122*-176*. Outside of this range your fuel mileage will suffer so you definitely want to be within this temp. range on the highway. In winter I have to block some of my cooler to keep temps. above 122*!

Quote:

Originally Posted by FrankEtier

I used the fittings I purchased from Godzilla Race Works. I supplied the hose, cooler core, and other fittings. They have a full kit now though.

https://www.godzillaraceworks.com/37...0z-g37-q50-q60

Are you using the VR transmission yet or still OE?

That's a nice line kit

and a good solution for those with leaky and/or degrading rubber lines.

FrankEtier · 07-17-2023, 04:28 AM

Quote:

Originally Posted by Tractionless

Nice, I'm NA with only spirited street driving and using the same Hayden core Z1 uses in their kit (purchased elsewhere), rubber lines with oetiker stepless and ABA Awab clamps which are stronger and provide for a better seal than T-bolts and without leaks.

I'm bypassing the OE "cooler" as my current summer trans. temps. are 122*-172* via gauge in the hot line coming from the trans.; therefore, the aftermarket cooler would be fighting the OE cooler heating the fluid to whatever my coolant temp is, typically 175-190* (170* stat.) which is obviously counterproductive.

Be careful not to cool under 122* as OE torque converter lockup is 122*-176*. Outside of this range your fuel mileage will suffer so you definitely want to be within this temp. range on the highway. In winter I have to block some of my cooler to keep temps. above 122*!

Are you using the VR transmission yet or still OE?

That's a nice line kit

and a good solution for those with leaky and/or degrading rubber lines.

Yes I have a VR30 7AT in my car.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
forced induction in australia	andylena	Australia/New Zealand	23	09-15-2016 12:52 PM
Forced Induction Reliability	spearfish25	Forced Induction	58	09-08-2013 12:14 PM
Forced induction	stiso	Northern California Region	8	11-28-2011 12:03 PM
Help don't want forced induction!!!!!	Mjthind	Engine & Drivetrain	64	05-04-2011 01:00 PM
Forced induction	Seth G	Forced Induction	13	04-09-2010 12:36 AM