MAF Intake from Z1...

ezred · 04-01-2013, 09:46 PM

?

XwChriswX · 04-01-2013, 09:40 PM

How about a pic of the whole engine bay for a look?

XwChriswX · 04-01-2013, 09:49 PM

A picture of the whole engine bay...

ezred · 04-01-2013, 09:58 PM

I'll get one for ya tommorow will you be online? If I remove the silver thing from both sides , the original lines should fit...that way, just the accordian pieces will be removed....

Pintsize725 · 04-01-2013, 10:01 PM

Quote:

Originally Posted by ezred

So is it ok to remove the silver thing from the silicone tubes? They could/would fit then right?

Thanks...

Yes, take that silver thing off, it does not get installed. Nissan 370Z Forum - Pintsize725's Album: Pintsize's PW - Picture

ezred · 04-01-2013, 10:06 PM

Thanks! it should fit then.....I'll post pic when its back together....other tips are also welcome,
Thanks...

Pintsize725 · 04-01-2013, 10:10 PM

Quote:

Originally Posted by ezred

Thanks! it should fit then.....I'll post pic when its back together....other tips are also welcome,
Thanks...

Passenger side might need to have the stock airbox removed for proper fitment. At least, that's what I had to do. Also, a butter knife helps tight spots. Good luck!

XwChriswX · 04-01-2013, 10:27 PM

Quote:

Originally Posted by ezred

I'll get one for ya tommorow will you be online? If I remove the silver thing from both sides , the original lines should fit...that way, just the accordian pieces will be removed....

That's how it is from the start. You don't remove anything from the maf tubes...

Pintsize725 · 04-01-2013, 10:52 PM

Quote:

Originally Posted by XwChriswX

That's how it is from the start. You don't remove anything from the maf tubes...

Yes you do. The tubes ship with a silver round insert in the parts that connect closer to the engine. It has to be removed.

XwChriswX · 04-01-2013, 10:54 PM

Quote:

Originally Posted by Pintsize725

Yes you do. The tubes ship with a silver round insert in the parts that connect closer to the engine. It has to be removed.

That part goes in the other tubes... I've had them, they worked just fine.

XwChriswX · 04-01-2013, 10:59 PM

I'm not sure what to tell you then, I've installed them on mine and 2 other cars with no problems.

critical · 04-01-2013, 11:58 PM

You should remove the metal inserts. They are used if you go with the Z1 Silicone Side PCV Breather Hose set for Aftermarket Intakes as well I believe.

ezred · 04-02-2013, 11:52 AM

http://www.the370z.com/attachment.ph...1&d=1364921446

http://www.the370z.com/attachment.ph...1&d=1364921446

Here's a couple pics of my finished project...

Mandingo · 04-02-2013, 01:51 PM

Pintsize is right. Those metal adaptors aren't used unless you have Z1's pcv tubes as well

04-01-2013, 09:40 PM	#2 (permalink)
XwChriswX WFLYIDNNE Join Date: Jul 2009 Location: In The Fastlane Posts: 50,648 Drives: 02 GDB WRX Rep Power: 453	How about a pic of the whole engine bay for a look? __________________ Bonnie - Stage 2, Audio build coming this fall! R.I.P. Abby 3/29/10 - 3/30/14

04-01-2013, 09:49 PM	#3 (permalink)
XwChriswX WFLYIDNNE Join Date: Jul 2009 Location: In The Fastlane Posts: 50,648 Drives: 02 GDB WRX Rep Power: 453	A picture of the whole engine bay... __________________ Bonnie - Stage 2, Audio build coming this fall! R.I.P. Abby 3/29/10 - 3/30/14

04-01-2013, 10:59 PM	#11 (permalink)
XwChriswX WFLYIDNNE Join Date: Jul 2009 Location: In The Fastlane Posts: 50,648 Drives: 02 GDB WRX Rep Power: 453	I'm not sure what to tell you then, I've installed them on mine and 2 other cars with no problems. __________________ Bonnie - Stage 2, Audio build coming this fall! R.I.P. Abby 3/29/10 - 3/30/14

04-02-2013, 01:51 PM	#14 (permalink)
Mandingo Track Member Join Date: Nov 2010 Location: Dallas Posts: 625 Drives: '10 370z 6spd Rep Power: 3371	Pintsize is right. Those metal adaptors aren't used unless you have Z1's pcv tubes as well __________________ some mods

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
I have K&N Cold Air Intake - Want to swap for Factory Intake	Troyz	Texas	2	03-27-2013 09:48 AM
370z Injen Speed Pro Series Intake \| AEM ETI Intake stupid pricing	Tunerz_Store	Exhaust/Intake	11	11-01-2010 01:43 PM

04-01-2013, 09:46 PM	#1 (permalink)
ezred Base Member Join Date: May 2011 Location: Red Wing MN Posts: 131 Drives: 2010 Red 370Z 7sp AT Rep Power: 15	?

04-01-2013, 09:58 PM	#4 (permalink)
ezred Base Member Join Date: May 2011 Location: Red Wing MN Posts: 131 Drives: 2010 Red 370Z 7sp AT Rep Power: 15	I'll get one for ya tommorow will you be online? If I remove the silver thing from both sides , the original lines should fit...that way, just the accordian pieces will be removed....

04-01-2013, 10:06 PM	#6 (permalink)
ezred Base Member Join Date: May 2011 Location: Red Wing MN Posts: 131 Drives: 2010 Red 370Z 7sp AT Rep Power: 15	Thanks! it should fit then.....I'll post pic when its back together....other tips are also welcome, Thanks...

04-01-2013, 11:58 PM	#12 (permalink)
critical A True Z Fanatic Join Date: Oct 2012 Location: Washington Posts: 1,252 Drives: 09' 370z 7AT Rep Power: 16	You should remove the metal inserts. They are used if you go with the Z1 Silicone Side PCV Breather Hose set for Aftermarket Intakes as well I believe.