Dreaded P0300

oro · 10-28-2011, 11:59 AM

I installed my ART pipes.about 2. weeks ago and hadn't experienced any problems till I.threw.a.solid.code.last.week.. so I tightened up the piping and reset the the ecu, now the.sel started.blinking, knowing that's a misfire.I.took it.to autozone to had.the.code.pulled and got random.multiple misfire.codes. Could the.ART Pipes have leaned out the af to cause.that condition? I'm idling high.at 1k rpm, if.i.reset the.sel the car will run normally till it throws.the.sel again. The.car doesn't appear.to have a misfire off idle and throws.a solid sel, once.you.get around 65 though, the.blinking.misfire.sel returns, thoughts?

MattP725 · 10-28-2011, 12:19 PM

My thoughts are get the car tuned ASAP, sounds like your AFR is really off... additionally they will remove the second o2 sensor so you don't throw CELs any more.

oro · 10-28-2011, 03:09 PM

Quote:

Originally Posted by MattP725

My thoughts are get the car tuned ASAP, sounds like your AFR is really off... additionally they will remove the second o2 sensor so you don't throw CELs any more.

I was planning on doing it after I got my exhaust installed but unfortunately it doesn't look like ill be able to wait that long now, have you or anyone else experienced this from tp's?

I've seen the code thrown from intake but none thus far on the forums from hfc's or tp's.

oro · 10-30-2011, 12:34 AM

Interesting development after resting the code a few times and driving at quarter to half throttle till I can get it tuned the code changed from multiple misfire to o2 sensor, bank 1 sensor 1, I'm assuming when I'm on part throttle the flow isn't enough to screw with fuel trims but when the car is somewhat pushed it screws with the A/F and causes the random misfire.

Z1804 · 10-30-2011, 12:58 AM

I had the same code after installing my ART pipes. Car was running rich. I replaced the ART pipes with Stillen HFCs. Code went off for a week and came back on. I had to take it to the dealer to get reset. I'm going to drive it for a while before I decide to put the ART pipes back on. If I decide to put them back on.

I did notice that the car is much slower with the HFCs though.

arnoldas · 01-26-2013, 04:32 PM

Sorry to bring up an old post but the same thing is happening to me now, I have test pipes and the cel is blinking, but it seems like there are no symptoms, no loss of power or Anything.

10-28-2011, 11:59 AM	#1 (permalink)
oro Base Member Join Date: Dec 2009 Location: Arizona Posts: 192 Drives: G37S Rep Power: 16	Dreaded P0300 I installed my ART pipes.about 2. weeks ago and hadn't experienced any problems till I.threw.a.solid.code.last.week.. so I tightened up the piping and reset the the ecu, now the.sel started.blinking, knowing that's a misfire.I.took it.to autozone to had.the.code.pulled and got random.multiple misfire.codes. Could the.ART Pipes have leaned out the af to cause.that condition? I'm idling high.at 1k rpm, if.i.reset the.sel the car will run normally till it throws.the.sel again. The.car doesn't appear.to have a misfire off idle and throws.a solid sel, once.you.get around 65 though, the.blinking.misfire.sel returns, thoughts?

10-30-2011, 12:58 AM	#5 (permalink)
Z1804 Premium Member Join Date: May 2010 Location: GA Posts: 784 Drives: 2009 370Z Sport M6 Rep Power: 17	I had the same code after installing my ART pipes. Car was running rich. I replaced the ART pipes with Stillen HFCs. Code went off for a week and came back on. I had to take it to the dealer to get reset. I'm going to drive it for a while before I decide to put the ART pipes back on. If I decide to put them back on. I did notice that the car is much slower with the HFCs though. __________________ Z1804 ------ Z1804 ------ Z1804 ------ ------ Z1804 ------ Z1804 ------ Z1804 Fairlady Z 2011 Calendar Now on Sale!!!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
P0300 cold mornings?	1slow370	Engine & Drivetrain	16	11-21-2013 01:59 PM
P0300 random misfire code HELP!	Alchemy	Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs	12	12-02-2011 05:34 PM
Dreaded engine won't start	cubarican84	Engine & Drivetrain	8	10-03-2011 09:31 AM
Code P0300 after CBE install	ProfessorDave	Engine & Drivetrain	10	10-26-2010 04:42 PM
Ah man, the dreaded SES	Red370	Nissan 370Z General Discussions	15	11-29-2009 07:40 PM

10-28-2011, 12:19 PM	#2 (permalink)
MattP725 A True Z Fanatic Join Date: May 2011 Location: Toms River, NJ Posts: 1,904 Drives: 2010 40th Rep Power: 18	My thoughts are get the car tuned ASAP, sounds like your AFR is really off... additionally they will remove the second o2 sensor so you don't throw CELs any more.

10-30-2011, 12:34 AM	#4 (permalink)
oro Base Member Join Date: Dec 2009 Location: Arizona Posts: 192 Drives: G37S Rep Power: 16	Interesting development after resting the code a few times and driving at quarter to half throttle till I can get it tuned the code changed from multiple misfire to o2 sensor, bank 1 sensor 1, I'm assuming when I'm on part throttle the flow isn't enough to screw with fuel trims but when the car is somewhat pushed it screws with the A/F and causes the random misfire.

01-26-2013, 04:32 PM	#6 (permalink)
arnoldas Base Member Join Date: Aug 2012 Location: new york Posts: 197 Drives: 09 Nissan 370Z M6 Rep Power: 13	Sorry to bring up an old post but the same thing is happening to me now, I have test pipes and the cel is blinking, but it seems like there are no symptoms, no loss of power or Anything.