P1233 Permanent Code

Optimiser · 07-20-2016, 10:24 PM

This morning while driving to work and stopped at the lights idling, the idle went up to about 1000rpm by itself, the engine light and the (2) VDC lights came on and the car would not go faster then walking speed with no throttle control. I turned the engine off and on again and the car drove normally (engine light still on) until I came to a stop again and the same thing happened as above.
My work around is when I'm stopped I use a bit of accelerator to keep the revs up around 1000rpm and when I get going again it drives normally. If however I let the engine drop back to its normal idle (about 650rpm) the whole issue starts again.
I can clear the codes using a scan tool and things again behave as they should, but after about a minute the problem starts again and "DashCommand" now tells me that the P1233 code is permanent.
Some research tells me that code is related to the Electric Throttle Control Performance-Bank 2. Apparently this can be related to the following:
1/. A faulty Electric Throttle Control actuator.
2/. ETC actuator harness open or shorted.
3/. ETC actuator circuit poor electrical connection.
My car has the Stillen SC kit that I think uses an extended lead to connect one of the throttle bodies, but I believe Bank-2 refers to the OEM lead.

If anyone has any info/suggestions I would love to hear them. Thanks.

TechnicZ · 07-20-2016, 11:02 PM

Quote:

Originally Posted by Optimiser

This morning while driving to work and stopped at the lights idling, the idle went up to about 1000rpm by itself, the engine light and the (2) VDC lights came on and the car would not go faster then walking speed with no throttle control. I turned the engine off and on again and the car drove normally (engine light still on) until I came to a stop again and the same thing happened as above.
My work around is when I'm stopped I use a bit of accelerator to keep the revs up around 1000rpm and when I get going again it drives normally. If however I let the engine drop back to its normal idle (about 650rpm) the whole issue starts again.
I can clear the codes using a scan tool and things again behave as they should, but after about a minute the problem starts again and "DashCommand" now tells me that the P1233 code is permanent.
Some research tells me that code is related to the Electric Throttle Control Performance-Bank 2. Apparently this can be related to the following:
1/. A faulty Electric Throttle Control actuator.
2/. ETC actuator harness open or shorted.
3/. ETC actuator circuit poor electrical connection.
My car has the Stillen SC kit that I think uses and extended lead to connect one of the throttle bodies, but I believe Bank-2 refers to the OEM lead.

If anyone has any info/suggestions I would love to hear them. Thanks.

Check continuity from the extension from the original OEM harness. A splice probably came loose from corrosion or weak link and the ECU isn't getting signal from the throttle body. Good luck.

Jhill · 07-21-2016, 01:46 PM

Quote:

Originally Posted by TechnicZ

Check continuity from the extension from the original OEM harness. A splice probably came loose from corrosion or weak link and the ECU isn't getting signal from the throttle body. Good luck.

Continuity doesn't really give you an accurate result, you are much better off back probing and checking for voltage drops and signals.

TechnicZ · 07-23-2016, 09:23 AM

Quote:

Originally Posted by Jhill

Continuity doesn't really give you an accurate result, you are much better off back probing and checking for voltage drops and signals.

One step at a time. Test the harness first before throwing parts at a vehicle. Take your time and do the tests to limit unnecessary repairs. Higher probability of a bad splice due to harness extension. Continuity/resistance test from the ecu to sensor connector would be ideal.

Sent from my SAMSUNG-SM-G935A using Tapatalk

Jhill · 07-23-2016, 01:13 PM

Quote:

Originally Posted by TechnicZ

One step at a time. Test the harness first before throwing parts at a vehicle. Take your time and do the tests to limit unnecessary repairs. Higher probability of a bad splice due to harness extension. Continuity/resistance test from the ecu to sensor connector would be ideal.

Sent from my SAMSUNG-SM-G935A using Tapatalk

Who said anything about throwing parts at it? I am saying to a voltage drop test from ecu to sensor, it is much more accurate then a resistance test. This is much more accurate to tell you if you have poor contact through your splice.

SouthArk370Z · 07-23-2016, 09:57 PM

While a continuity check is usually good enough for on/off circuits (lighting, motors, &c), as per Jhill, checking the circuit while it is in operation is the best way to check control circuits. A small wiring problem may pass the "sniff test" of a continuity checker but still cause signal problems.

DOOMMONKEY777 · 07-27-2016, 10:00 PM

Take off the TB and push the valve butterfly with your finger make sure it goes from full open to full closed position, it seems to be stuck open a little.

Optimiser · 07-27-2016, 10:13 PM

Thank you all for your replies.
I now have the car at my tuner and am waiting to hear back from them as to what it is.
I will report back as soon as I as I know.

Optimiser · 07-30-2016, 12:59 AM

It turned out to be just 1 of the pins of the plug on the extension lead (for SC kit) for one of the throttle bodies actuator motor, having a slightly bad connection.

Jhill · 07-30-2016, 12:32 PM

Quote:

Originally Posted by Optimiser

It turned out to be just 1 of the pins of the plug on the extension lead (for SC kit) for one of the throttle bodies actuator motor, having a slightly bad connection.

Cool, good deal. Figured you just had a connection issue.

Maybe2wice · 10-28-2019, 07:37 AM

Quote:

Originally Posted by Optimiser

Thank you all for your replies.
I now have the car at my tuner and am waiting to hear back from them as to what it is.
I will report back as soon as I as I know.

How is your running after the fix?

Optimiser · 10-28-2019, 08:24 PM

Quote:

Originally Posted by Maybe2wice

How is your running after the fix?

More reliably now.

07-20-2016, 10:24 PM	#1 (permalink)
Optimiser Enthusiast Member Join Date: Mar 2013 Location: Australia Posts: 456 Drives: 2012 Nissan 370Z MT Rep Power: 20145	P1233 Permanent Code This morning while driving to work and stopped at the lights idling, the idle went up to about 1000rpm by itself, the engine light and the (2) VDC lights came on and the car would not go faster then walking speed with no throttle control. I turned the engine off and on again and the car drove normally (engine light still on) until I came to a stop again and the same thing happened as above. My work around is when I'm stopped I use a bit of accelerator to keep the revs up around 1000rpm and when I get going again it drives normally. If however I let the engine drop back to its normal idle (about 650rpm) the whole issue starts again. I can clear the codes using a scan tool and things again behave as they should, but after about a minute the problem starts again and "DashCommand" now tells me that the P1233 code is permanent. Some research tells me that code is related to the Electric Throttle Control Performance-Bank 2. Apparently this can be related to the following: 1/. A faulty Electric Throttle Control actuator. 2/. ETC actuator harness open or shorted. 3/. ETC actuator circuit poor electrical connection. My car has the Stillen SC kit that I think uses an extended lead to connect one of the throttle bodies, but I believe Bank-2 refers to the OEM lead. If anyone has any info/suggestions I would love to hear them. Thanks. Last edited by Optimiser; 07-28-2016 at 07:25 AM.

07-23-2016, 09:57 PM	#6 (permalink)
SouthArk370Z Premium Member Join Date: Nov 2010 Location: South Arkansas Posts: 8,435 Drives: 2014 Challenger Rep Power: 324198	While a continuity check is usually good enough for on/off circuits (lighting, motors, &c), as per Jhill, checking the circuit while it is in operation is the best way to check control circuits. A small wiring problem may pass the "sniff test" of a continuity checker but still cause signal problems. jrb55gh and Jhill like this. __________________ Steering Lock Links - Search The370Z Bookmarklet - FSM @ NICOclub Mankind has progressed past the need for war but we haven't evolved that far. - NachoMahma

07-27-2016, 10:00 PM	#7 (permalink)
DOOMMONKEY777 A True Z Fanatic Join Date: Sep 2010 Location: Crooklyn Posts: 1,012 Drives: 370Z 6psd-sport-pkg Rep Power: 21	Take off the TB and push the valve butterfly with your finger make sure it goes from full open to full closed position, it seems to be stuck open a little. __________________ Kids don't do Drugs, Drugs are bad, so let the professional druggies do Drugs for you. 537whp/496lb/tq@8-9PSI 93 octane

07-27-2016, 10:13 PM	#8 (permalink)
Optimiser Enthusiast Member Join Date: Mar 2013 Location: Australia Posts: 456 Drives: 2012 Nissan 370Z MT Rep Power: 20145	Thank you all for your replies. I now have the car at my tuner and am waiting to hear back from them as to what it is. I will report back as soon as I as I know. wideglideleon likes this. Last edited by Optimiser; 07-28-2016 at 07:31 AM.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Code p200.a/f code help	YzGyz	Tuning	2	11-15-2015 09:11 PM
permanent dtc codes	hindi1973	Forced Induction	30	02-01-2015 07:41 AM
How to sticky-mount your GoPro without it being permanent.	Arrvaxx	Audio & Video	1	08-25-2014 11:46 AM
P0300 code - SES Light came on, got the code verified, now the light is off	kittens	Engine & Drivetrain	1	12-26-2013 06:02 PM

07-30-2016, 12:59 AM	#9 (permalink)
Optimiser Enthusiast Member Join Date: Mar 2013 Location: Australia Posts: 456 Drives: 2012 Nissan 370Z MT Rep Power: 20145	It turned out to be just 1 of the pins of the plug on the extension lead (for SC kit) for one of the throttle bodies actuator motor, having a slightly bad connection.