DIY: Air conditioning for your Sump!.......

gufazi · 09-26-2010, 07:00 AM

Interested. Do you have any pics of the install. Where exactly did you put them?

Jordo! · 09-26-2010, 11:32 AM

Quote:

Originally Posted by gufazi

Interested. Do you have any pics of the install. Where exactly did you put them?

It comes with a heat conductive double sided adhesive strip -- a small square that is exactly the same size as the fins. Two sets of fins covers about 3/4 of the bottom of the oil pan. Put the strip down, gently press on the fins -- done.

If you wanted to do the oil pan and, say, the diff case -- I'd order 4-5 sets of them.

Decoy_TT · 09-26-2010, 01:36 PM

Hey Jordo, I was just browsing around on this site and noticed you're also in Tampa...

I've been tossing the idea of buying myself a Z34 in addition to my TT Z32... Care to meet up and give me an in depth look at your 370z? I already have a few Z buddies around town and wouldn't mind one more.

What say you? I could try and get a meet going or something.

(Sorry for off topic!)

RCGsupra · 09-26-2010, 02:40 PM

Quote:

Originally Posted by Jordo!

Quick update -- I have the cool fins on. As soon as they were afixed, you could feel heat being pulled off of the oil pan.

Now I also switched to 0-w30 Castrol, so not 100% certain that the cool fins are soley responsible for this, but after romping on it very hard in 90* F FL heat, oil temps stayed below 220 the whole time

I'll monitor temps suring normal driving and report more later

Keep us posted. I'm interested in seeing if this is effective. I know it's a pipe dream, but it would be awesome if these could be used instead of an oil cooler,

Jordo! · 09-26-2010, 04:08 PM

Quote:

Originally Posted by Decoy_TT

Hey Jordo, I was just browsing around on this site and noticed you're also in Tampa...

I've been tossing the idea of buying myself a Z34 in addition to my TT Z32... Care to meet up and give me an in depth look at your 370z? I already have a few Z buddies around town and wouldn't mind one more.

What say you? I could try and get a meet going or something.

(Sorry for off topic!)

I'm pretty insanely busy these days, but shoot me a PM. If beer is involved, I can usually find time -- ha ha ha

Quote:

Originally Posted by RCGsupra

Keep us posted. I'm interested in seeing if this is effective. I know it's a pipe dream, but it would be awesome if these could be used instead of an oil cooler,

Will do -- if it can even pull 10* F out of the oil, I figure it's worth it for anyone who hasn't seen insanely high temps. I've never seen mine go over 230*, so it should be sufficient for me, for instance.

Decoy_TT · 09-26-2010, 04:48 PM

You don't have to say that twice. I'll buy ya a round in order to check out the 370z and shoot the **** with a fellow Zer, no problem there. lol.

Let's meet up in a few weeks? I have a ways off fro buying my Z and it will be my first new car purchase so I'm taking my time... No hurry but if you're bored one weekend shoot me a PM and we can meet up. Just gotta tell my gf i'm gonna ignore her for a night and i'm good to go

And to stay on topic, this is def. interesting. If/when my purchase happens, I'd try this in a heartbeat... Especially in our heat.

Jordo! · 09-26-2010, 10:37 PM

Quote:

Originally Posted by Decoy_TT

You don't have to say that twice. I'll buy ya a round in order to check out the 370z and shoot the **** with a fellow Zer, no problem there. lol.

Let's meet up in a few weeks? I have a ways off fro buying my Z and it will be my first new car purchase so I'm taking my time... No hurry but if you're bored one weekend shoot me a PM and we can meet up. Just gotta tell my gf i'm gonna ignore her for a night and i'm good to go

And to stay on topic, this is def. interesting. If/when my purchase happens, I'd try this in a heartbeat... Especially in our heat.

Will do

So far I'm seeing crusing temps around 180 - 210, which is maybe 5-10* cooler than usual, but I'll know better during my commute tomorrow.

I suppose I might even slap on a few more of these on the sides of the pan.

Most of the heat going into the oil is from the engine, of course, so my guess is that this will drop temps AT BEST by 10 -15* F.

That said, if you aren't seeing temps over 230* F, that's pretty reasonable for ~20 bucks a set of fins and the easiest install in the world.

egz · 10-01-2010, 07:14 PM

nice job with the fins!! do you have any pics??

Jordo! · 10-01-2010, 09:26 PM

Quote:

Originally Posted by egz

nice job with the fins!! do you have any pics??

No, sorry -- they are just stuck to the bottom of the oil pan. Next oil change I may add a few more and can get a pic then if anyone wants to see it.

I'd like to see what adding two more do -- so far it does appear to bring the averagetemp down < 10*F, but that's not too shabby for such a simple and inexpensive modification.

'10Anamoly · 07-31-2012, 02:12 PM

I added two sets of the ARC cool fins to my oil pan and cut out a small rear vent in the back behind the oil pan to encourage some air flow out. Also removed the top center plastic piece and adjusted the weatherstripping so air can flow in and out of the hood area in the middle.

Will have results soon. The top plastic adjustment and weatherstripping is completely reversible in case of a rainy day which is nice!

Jordo! · 12-21-2013, 03:13 PM

Thread revival II:

Can anyone recommend a short (meaning doesn't stick out from under plastics much) ABS vent similar to the the one modshack used?

I'm thinking of adding one that is open in front and back to flow air through and even offer a tiny bit of extra downforce if anything.

Problem: Does any air even flow under there, at least on the sport package?

The front chin spoiler might keep air from ducking unde there, and if no air is going under there anyway, a few slits and (maybe a piece of mesh for rocks?) is more than enough.

If some air does flow, then a little rectangular duct, ported on both sides, should cool the sump, especially with added heat sinks (I have the arc cool fins, which work really, really well).

Thoughts?

wstar · 12-23-2013, 10:04 AM

There will be plenty of air movement in that area in general already, but getting the pressure and flow in the right direction(s) would be tricky. If any air is flowing through holes in the undertray, you want it to be upwards flow (sucking from the ground up into the engine bay), so that it's moving in the direction that helps rather than hurts front downforce. The potential problem is that, assuming the rest of the bay/hood is stock, there might be so much air pressure from the backside of the radiator that any vent you cut down there ends up flowing outwards and screwing that up. I really have no idea, all you could do is guess/test. If you had a hood vented to exhaust the pressure from the backside of the rad fans upwards (as is being discussed endlessly in other threads currently) the pressure would be a non-issue, but then you'd probably have plenty of airflow in/around there without cutting any new slits anyways.

Either way, I don't think it would be a good idea in any scenario to cut any slits/holes in the front chin spoiler.

Jordo! · 12-27-2013, 08:54 AM

Quote:

Originally Posted by wstar

There will be plenty of air movement in that area in general already, but getting the pressure and flow in the right direction(s) would be tricky. If any air is flowing through holes in the undertray, you want it to be upwards flow (sucking from the ground up into the engine bay), so that it's moving in the direction that helps rather than hurts front downforce. The potential problem is that, assuming the rest of the bay/hood is stock, there might be so much air pressure from the backside of the radiator that any vent you cut down there ends up flowing outwards and screwing that up. I really have no idea, all you could do is guess/test. If you had a hood vented to exhaust the pressure from the backside of the rad fans upwards (as is being discussed endlessly in other threads currently) the pressure would be a non-issue, but then you'd probably have plenty of airflow in/around there without cutting any new slits anyways.

Either way, I don't think it would be a good idea in any scenario to cut any slits/holes in the front chin spoiler.

Oh sorry -- I wasn't clear at all on that.

I meant, "to cut slits in the under panel", not the chin spoiler, but the rest of your explanation is pretty much what I figured: either a crap shoot without testing or will do no additional cooling.

Jordo! · 06-06-2014, 11:15 AM

For those who were asking before -- ta daaaa

Behold. Ugly but functional:

I also have two stuck on my diff cover

07-31-2012, 02:12 PM	#40 (permalink)
'10Anamoly Track Member Join Date: May 2010 Location: GA Posts: 882 Drives: 2010 370Z BS M6 Rep Power: 17	I added two sets of the ARC cool fins to my oil pan and cut out a small rear vent in the back behind the oil pan to encourage some air flow out. Also removed the top center plastic piece and adjusted the weatherstripping so air can flow in and out of the hood area in the middle. Will have results soon. The top plastic adjustment and weatherstripping is completely reversible in case of a rainy day which is nice! __________________ 2013 Ford Mustang GT 374rwhp, 360rwtq SAE / GT500 Axle-Backs / Brembo Pack / Track Pack / Recaros / 6spd

12-21-2013, 03:13 PM	#41 (permalink)
Jordo! A True Z Fanatic Join Date: May 2010 Location: nirvana Posts: 6,394 Drives: 2023 NATM Rep Power: 419	Thread revival II: Can anyone recommend a short (meaning doesn't stick out from under plastics much) ABS vent similar to the the one modshack used? I'm thinking of adding one that is open in front and back to flow air through and even offer a tiny bit of extra downforce if anything. Problem: Does any air even flow under there, at least on the sport package? The front chin spoiler might keep air from ducking unde there, and if no air is going under there anyway, a few slits and (maybe a piece of mesh for rocks?) is more than enough. If some air does flow, then a little rectangular duct, ported on both sides, should cool the sump, especially with added heat sinks (I have the arc cool fins, which work really, really well). Thoughts? __________________ Enjoy it. Destroy it.

12-23-2013, 10:04 AM	#42 (permalink)
wstar A True Z Fanatic Join Date: Mar 2009 Location: Houston, TX Posts: 4,024 Drives: too slow Rep Power: 3595	There will be plenty of air movement in that area in general already, but getting the pressure and flow in the right direction(s) would be tricky. If any air is flowing through holes in the undertray, you want it to be upwards flow (sucking from the ground up into the engine bay), so that it's moving in the direction that helps rather than hurts front downforce. The potential problem is that, assuming the rest of the bay/hood is stock, there might be so much air pressure from the backside of the radiator that any vent you cut down there ends up flowing outwards and screwing that up. I really have no idea, all you could do is guess/test. If you had a hood vented to exhaust the pressure from the backside of the rad fans upwards (as is being discussed endlessly in other threads currently) the pressure would be a non-issue, but then you'd probably have plenty of airflow in/around there without cutting any new slits anyways. Either way, I don't think it would be a good idea in any scenario to cut any slits/holes in the front chin spoiler. __________________ 7AT Track Car! Journal thread / Car setup details

06-06-2014, 11:15 AM	#44 (permalink)
Jordo! A True Z Fanatic Join Date: May 2010 Location: nirvana Posts: 6,394 Drives: 2023 NATM Rep Power: 419	For those who were asking before -- ta daaaa Behold. Ugly but functional: I also have two stuck on my diff cover Bullit79 likes this. __________________ Enjoy it. Destroy it.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Air conditioning knocking noise	MagnumPI	Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs	10	09-14-2020 03:55 AM
Air Conditioning Problem	toplessdottie	Engine & Drivetrain	26	07-30-2016 09:59 AM
Air Conditioning Bad Smell	bradcc	Exterior & Interior	14	05-13-2011 04:55 PM
Air Conditioning problem	toc2rta	Nissan 370Z Owners Manual / Service Manuals	1	03-31-2010 07:58 PM

09-26-2010, 07:00 AM	#31 (permalink)
gufazi Base Member Join Date: Jul 2010 Location: Springfield, Virginia Posts: 28 Drives: 09 370Z Tour Sport Rep Power: 16	Interested. Do you have any pics of the install. Where exactly did you put them?

09-26-2010, 01:36 PM	#33 (permalink)
Decoy_TT Base Member Join Date: Sep 2010 Location: Tampa, Fl Posts: 54 Drives: 1990 300zx TT Rep Power: 15	Hey Jordo, I was just browsing around on this site and noticed you're also in Tampa... I've been tossing the idea of buying myself a Z34 in addition to my TT Z32... Care to meet up and give me an in depth look at your 370z? I already have a few Z buddies around town and wouldn't mind one more. What say you? I could try and get a meet going or something. (Sorry for off topic!)

09-26-2010, 04:48 PM	#36 (permalink)
Decoy_TT Base Member Join Date: Sep 2010 Location: Tampa, Fl Posts: 54 Drives: 1990 300zx TT Rep Power: 15	You don't have to say that twice. I'll buy ya a round in order to check out the 370z and shoot the **** with a fellow Zer, no problem there. lol. Let's meet up in a few weeks? I have a ways off fro buying my Z and it will be my first new car purchase so I'm taking my time... No hurry but if you're bored one weekend shoot me a PM and we can meet up. Just gotta tell my gf i'm gonna ignore her for a night and i'm good to go And to stay on topic, this is def. interesting. If/when my purchase happens, I'd try this in a heartbeat... Especially in our heat.

10-01-2010, 07:14 PM	#38 (permalink)
egz Base Member Join Date: Sep 2010 Location: Chicago Posts: 42 Drives: 09 370z tour s rd m6 Rep Power: 15	nice job with the fins!! do you have any pics??