Has anyone been able to install a Z1 master cylinder brace?

gshort24 · 08-02-2016, 08:58 PM

I've spend a few hours trying to thread the 3 screws in to hold the brace in place. The instuctions over simplify the install. I've tried multiple tools and wrench extensions with no luck. Is it actually possible to install without removing the master cylinder? It's probably going to be a $90 paper weight.

seboderus · 08-08-2016, 08:44 PM

It took me close to an hour to install mine. I used a long extension and a swivel. I also put electrical tape on my hex socket to hold the bolt while I positioned the bracket with my left hand. I put the outside bolts in first and i never could get the center one to align. I tried my best but ended up cross threading it and i just left it out. i felt i difference after the install.

abm89 · 08-11-2016, 01:46 PM

Use some gummy substance to hold the screws in place while you have someone with small hands thread them into the car.

It was a PITA to install, but definitely helps.

Jhill · 08-11-2016, 02:03 PM

So you guys that have one have actually noticed a difference? Seems kinda unbelievable to me as the brakes are still super strong without, especially with the track pads in.

abm89 · 08-11-2016, 02:05 PM

I already had Stainless lines, But I could feel a tad bit of play in the pedal. After installing the brace, the play almost un-noticeable.

08-02-2016, 08:58 PM	#1 (permalink)
gshort24 Base Member Join Date: Jul 2015 Location: California Posts: 22 Drives: 2009 370Z Rep Power: 9	Has anyone been able to install a Z1 master cylinder brace? I've spend a few hours trying to thread the 3 screws in to hold the brace in place. The instuctions over simplify the install. I've tried multiple tools and wrench extensions with no luck. Is it actually possible to install without removing the master cylinder? It's probably going to be a $90 paper weight.

08-11-2016, 01:46 PM	#3 (permalink)
abm89 A True Z Fanatic Join Date: Feb 2013 Location: Austin, Texas Posts: 1,299 Drives: 11 370Z \| 24 EL450 Rep Power: 64763	Use some gummy substance to hold the screws in place while you have someone with small hands thread them into the car. It was a PITA to install, but definitely helps. __________________ Complete Parts List: https://github.com/abm89/ztouge-build

08-11-2016, 02:05 PM	#5 (permalink)
abm89 A True Z Fanatic Join Date: Feb 2013 Location: Austin, Texas Posts: 1,299 Drives: 11 370Z \| 24 EL450 Rep Power: 64763	I already had Stainless lines, But I could feel a tad bit of play in the pedal. After installing the brace, the play almost un-noticeable. __________________ Complete Parts List: https://github.com/abm89/ztouge-build Last edited by abm89; 08-11-2016 at 05:20 PM.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Z1 Master cylinder brace installed.	Mike	Brakes & Suspension	47	04-14-2021 03:23 AM
Bad Master Cylinder?	ARrado15	Engine & Drivetrain	6	04-17-2016 04:30 AM
[WTB] Need a Clutch Master Cylinder	guzmanb66	Parts for sale (Private Classifieds)	11	03-13-2015 12:42 PM
Master cylinder	Elmo370z	Engine & Drivetrain	4	01-05-2015 01:21 PM
Clutch master cylinder went out again	Zenmaster	Engine & Drivetrain	4	03-26-2013 12:54 AM

08-08-2016, 08:44 PM	#2 (permalink)
seboderus Base Member Join Date: Mar 2016 Location: NC Posts: 2 Drives: 11 Z34 RAE MT Rep Power: 9	It took me close to an hour to install mine. I used a long extension and a swivel. I also put electrical tape on my hex socket to hold the bolt while I positioned the bracket with my left hand. I put the outside bolts in first and i never could get the center one to align. I tried my best but ended up cross threading it and i just left it out. i felt i difference after the install.

08-11-2016, 02:03 PM	#4 (permalink)
Jhill Track Member Join Date: Mar 2016 Location: San jose Posts: 846 Drives: 2013 370z sport Rep Power: 3384	So you guys that have one have actually noticed a difference? Seems kinda unbelievable to me as the brakes are still super strong without, especially with the track pads in.