2013 370z Door Molex

zoomzoom · 07-07-2013, 05:11 PM

I just completed a speaker install on a 2013 sport version. Lots of the molex connector has no pins or wires in it which I was able to Dremel through. Its easiest to see what's going on if you unclip the cover on the molex connector and slip off the rubber boot to get to the connector back and wires.

bigaudiofanat · 07-07-2013, 06:13 PM

Quote:

Originally Posted by zoomzoom

I just completed a speaker install on a 2013 sport version. Lots of the molex connector has no pins or wires in it which I was able to Dremel through. Its easiest to see what's going on if you unclip the cover on the molex connector and slip off the rubber boot to get to the connector back and wires.

That was my plan! Glad you confirmed it before I got there. Ill be sire to do a write up on it.

Rectorna · 07-13-2013, 08:15 PM

Well just finished up the install.

Seems I left my Bit Ten D setup CD in my old car when I traded it in so I am trying to find the downloads right now.

Could not find molex pins so ended up just dremeling a hole big enough for the speaker wire.

Thanks for the suggestion to use wire lube really helped out a lot!

Now time to spend hour after hour tuning!

Thanks for the help!

Baer383 · 07-24-2013, 06:31 PM

I am getting ready to install my system in my 2013 Nismo and I took the door Molex connector apart and mine is the same as is was on my 2010 sport/touring.

bigaudiofanat · 07-24-2013, 06:41 PM

Quote:

Originally Posted by Baer383

I am getting ready to install my system in my 2013 Nismo and I took the door Molex connector apart and mine is the same as is was on my 2010 sport/touring.

Must of been right before they switched over. Or the OP's could have an extra add on that takes up that blank.Time will tell.

Baer383 · 07-24-2013, 06:55 PM

Quote:

Originally Posted by bigaudiofanat

Must of been right before they switched over. Or the OP's could have an extra add on that takes up that blank.Time will tell.

I'm glad b/c it was a lot easier to install 16ga wire thru there.

07-13-2013, 08:15 PM	#3 (permalink)
Rectorna Base Member Join Date: Feb 2012 Location: Virginia tech Posts: 69 Drives: 2013 PW 370z Sport Rep Power: 15	Well just finished up the install. Seems I left my Bit Ten D setup CD in my old car when I traded it in so I am trying to find the downloads right now. Could not find molex pins so ended up just dremeling a hole big enough for the speaker wire. Thanks for the suggestion to use wire lube really helped out a lot! Now time to spend hour after hour tuning! Thanks for the help! __________________ Cazper 2013 PW 370z 6MT Sport Fast Intentions l Swifts l Stillen \| Z1 l RJM l SPC l Focal l Audison l JL l LEDs l 20% Tint \| Vinyl l PlastiDip l OptiCoat

07-24-2013, 06:31 PM	#4 (permalink)
Baer383 A True Z Fanatic Join Date: Aug 2010 Location: Lawrenceville,Ga Posts: 4,293 Drives: My foot up your azz Rep Power: 31	I am getting ready to install my system in my 2013 Nismo and I took the door Molex connector apart and mine is the same as is was on my 2010 sport/touring. __________________ 2013 ZL1 754 rwhp 747 rwtq

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: Door Panel Removal & Door Speaker Size	jikhead	DIY Section (Do-It-Yourself)	46	07-16-2016 10:04 PM
Door 370Z - 2011 Question?	patchenkou	Exterior & Interior	0	10-10-2011 03:01 PM
Right Door for 370z	Z Monster	Wanted	0	03-12-2011 11:48 AM
370Z gas cap door problems	freddiebear	Exterior & Interior	42	05-15-2010 09:31 AM
Molex Removal?	SlikNik	Audio & Video	8	10-16-2009 05:21 AM

07-07-2013, 05:11 PM	#1 (permalink)
zoomzoom Base Member Join Date: Jul 2013 Location: the Lou Posts: 2 Drives: 2013 370z Sport M6 Rep Power: 13	I just completed a speaker install on a 2013 sport version. Lots of the molex connector has no pins or wires in it which I was able to Dremel through. Its easiest to see what's going on if you unclip the cover on the molex connector and slip off the rubber boot to get to the connector back and wires.