Calling on audiobigfanat

What-a-Rush · 10-07-2013, 02:57 PM

I just bought this camera and navtool. It seems like everything connects easy, however, there are 5 wires still left. Do these have to be connected?

bigaudiofanat · 10-07-2013, 07:18 PM

The 5 wires your mentioned I am going to assume at least two of them are for power probably switched 12 volt and Ground. can you get a close up of the wires that are left over?

Also where in NJ are you located?

What-a-Rush · 10-07-2013, 09:48 PM

This is a pic of the wires

bigaudiofanat · 10-07-2013, 09:54 PM

Ya I am pretty sure 2 of them are for power. What do the labels say on them?

What-a-Rush · 10-07-2013, 10:27 PM

Orange wire: reverse +12v input
Red wire: accessory +12v input
Black: ground
yellow: push button input
grey: parking brake

these wires are wrapped with a tag that say NI24.
The reason I ask is because the instructions say, "NI24pin: connect&play harness behind navigation screen only"

RonRizz · 10-09-2013, 06:52 PM

seems 2 me you answered your own question.

bigaudiofanat · 10-09-2013, 09:13 PM

Quote:

Originally Posted by What-a-Rush

Orange wire: reverse +12v input
Red wire: accessory +12v input
Black: ground
yellow: push button input
grey: parking brake

these wires are wrapped with a tag that say NI24.
The reason I ask is because the instructions say, "NI24pin: connect&play harness behind navigation screen only"

As Ron said all these wire have to be wired to the proper locations and which not all of them are directly behind the nav.

Fountainhead · 10-14-2013, 02:00 PM

Hi Rush,

What I did with my install was to take a cable that had several small wires (discrete and insulated from one another) (to match one for one the loose wires), connect, shrinkwrap and secure the loose wires into the multiwire cable at the rear of the Navi screen, and then run that multi-wire cable down the radio/AC/Navi box to the other side of the shift knob. Then, I connected those wires to the correct locations in the automobile.

Keep in mind there are several explicit detailed how to's that I found in the forum by using search. I studied the install of several other DIY's using the same kit and by the time the adapter arrived, I wired it without the instructions, I had read the DIY's so many times, haha.

It's not that difficult if you study and prepare ahead of time.

10-07-2013, 07:18 PM	#2 (permalink)
bigaudiofanat Car Audio Installer Join Date: Jun 2009 Location: Magnolia DE Posts: 8,342 Drives: 2012 Infiniti G37x Rep Power: 852	The 5 wires your mentioned I am going to assume at least two of them are for power probably switched 12 volt and Ground. can you get a close up of the wires that are left over? Also where in NJ are you located? __________________ Need help with car audio or electronics? Let me know!! Need Help Let Me Know Direct email address reimermatt@gmail.com Owner of: Dynamic Mobile Audio Follow me below https://www.facebook.com/Dynamicmobileaudio/

10-07-2013, 09:54 PM	#4 (permalink)
bigaudiofanat Car Audio Installer Join Date: Jun 2009 Location: Magnolia DE Posts: 8,342 Drives: 2012 Infiniti G37x Rep Power: 852	Ya I am pretty sure 2 of them are for power. What do the labels say on them? __________________ Need help with car audio or electronics? Let me know!! Need Help Let Me Know Direct email address reimermatt@gmail.com Owner of: Dynamic Mobile Audio Follow me below https://www.facebook.com/Dynamicmobileaudio/

10-09-2013, 06:52 PM	#6 (permalink)
RonRizz A True Z Fanatic Join Date: Aug 2011 Location: Pine grove, Pa Posts: 2,132 Drives: 2 feet, 3 pedals Rep Power: 6774	seems 2 me you answered your own question. __________________ P99rs Head Unit--- Amps- 2 Pioneer Prs800d --- Zapco ST1000MX---Zapco ST-4XSQ---- SI BM mk5 Subs---SI TM65v2 Midbass--- SI M3 mids--- SI M25 xbl2 tweeters ----- 2016 MECA street class 3rd place at world finals

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Calling Vendors to PM me	ddvette9	Suspension/Brakes	6	01-06-2012 05:53 PM
Calling all sc z car owners!	foxcrazy	South East Region	24	08-23-2011 10:06 AM
Calling all Bikers!!!	Togo	Other Vehicles	173	07-10-2011 10:15 PM
Calling all CarZ!!!!!!!!	Mont	Southern Region	0	08-03-2010 11:21 PM
Calling all web designers	molamann	The Lounge (Off Topic)	4	05-24-2009 11:45 PM

10-07-2013, 10:27 PM	#5 (permalink)
What-a-Rush Base Member Join Date: Aug 2013 Location: New Jersey Posts: 27 Drives: 09 370Z; 6 spd Rep Power: 11	Orange wire: reverse +12v input Red wire: accessory +12v input Black: ground yellow: push button input grey: parking brake these wires are wrapped with a tag that say NI24. The reason I ask is because the instructions say, "NI24pin: connect&play harness behind navigation screen only"

10-14-2013, 02:00 PM	#8 (permalink)
Fountainhead Track Member Join Date: Feb 2013 Location: FL Posts: 834 Drives: 2019 Civic Type R Rep Power: 14	Hi Rush, What I did with my install was to take a cable that had several small wires (discrete and insulated from one another) (to match one for one the loose wires), connect, shrinkwrap and secure the loose wires into the multiwire cable at the rear of the Navi screen, and then run that multi-wire cable down the radio/AC/Navi box to the other side of the shift knob. Then, I connected those wires to the correct locations in the automobile. Keep in mind there are several explicit detailed how to's that I found in the forum by using search. I studied the install of several other DIY's using the same kit and by the time the adapter arrived, I wired it without the instructions, I had read the DIY's so many times, haha. It's not that difficult if you study and prepare ahead of time.