2013 370z Door Molex

Rectorna · 06-17-2013, 04:15 PM

So I was trying to install my speakers today and got most of the interior taken apart. Then I went to start my speaker install and was trying to figure out how to run the wires though the molex so I watch the install videos and I ran into a problem.

I don't know if I am just not using my head or if the 2013 has a different molex but the male in my car does not look anything like the one in the videos or the ones I have seen in post and I cannot figure out how to get the wire though it.

ImageUploadedByTapatalk1371503397.980131.jpg

Is this the normal one or did they change it for 2013?

I am not seeing an easy way of getting my 12 gauge though the molex.

Thanks for any help!

fuct · 06-17-2013, 05:15 PM

looks different than i remember my 2010 piece looking..

Rectorna · 06-17-2013, 09:48 PM

Quote:

Originally Posted by fuct

looks different than i remember my 2010 piece looking..

Thats what I was worried about...

Anyone put speakers in there 2013 yet?

bigaudiofanat · 06-17-2013, 10:11 PM

Is this a convertible? I know they use that blank. Pull the rubber back and see if there are wires in all the slots of the green molex location.

Also no need for 12 gauge man, go with 16 gauge way easier and you can still run plenty of power through it.

Rectorna · 06-17-2013, 10:18 PM

Quote:

Originally Posted by bigaudiofanat

Is this a convertible? I know they use that blank. Pull the rubber back and see if there are wires in all the slots of the green molex location.

Also no need for 12 gauge man, go with 16 gauge way easier and you can still run plenty of power through it.

It is not a convertible. It seems that I can get the whole plastic connector apart. How do I do that. And I already have all the 12 gauge ku wire from my pervious car.

bigaudiofanat · 06-18-2013, 07:29 AM

Quote:

Originally Posted by Rectorna

It is not a convertible. It seems that I can get the whole plastic connector apart. How do I do that. And I already have all the 12 gauge ku wire from my pervious car.

There should be a clip releasing the plastic assembly around the molex connector, after that just pull the rubber grommet off the white section to look at the back.

Cbtech · 06-18-2013, 04:01 PM

Quote:

Originally Posted by Rectorna

It is not a convertible. It seems that I can get the whole plastic connector apart. How do I do that. And I already have all the 12 gauge ku wire from my pervious car.

you're going to HATE your life if you use larger speaker wire than 16 gauge while routing it through the plug and rubber boot. also id suggest using a water based wire lube to get through the boot.

Wire Lube

killerb87 · 07-04-2013, 02:35 PM

I have a 2013 sport. I used the rubber grommet behind the molex connector. Then just ran the wire through the door boot and siliconed both ends. worked great for me.

bigaudiofanat · 07-04-2013, 03:45 PM

I will have my first 2013 z install this coming week I will research and get back what I find.

Rectorna · 07-05-2013, 04:40 AM

I have been trying to find molex pins.

Look forward to seeing what you end up doing!

zoomzoom · 07-07-2013, 05:11 PM

I just completed a speaker install on a 2013 sport version. Lots of the molex connector has no pins or wires in it which I was able to Dremel through. Its easiest to see what's going on if you unclip the cover on the molex connector and slip off the rubber boot to get to the connector back and wires.

bigaudiofanat · 07-07-2013, 06:13 PM

Quote:

Originally Posted by zoomzoom

I just completed a speaker install on a 2013 sport version. Lots of the molex connector has no pins or wires in it which I was able to Dremel through. Its easiest to see what's going on if you unclip the cover on the molex connector and slip off the rubber boot to get to the connector back and wires.

That was my plan! Glad you confirmed it before I got there. Ill be sire to do a write up on it.

Rectorna · 07-13-2013, 08:15 PM

Well just finished up the install.

Seems I left my Bit Ten D setup CD in my old car when I traded it in so I am trying to find the downloads right now.

Could not find molex pins so ended up just dremeling a hole big enough for the speaker wire.

Thanks for the suggestion to use wire lube really helped out a lot!

Now time to spend hour after hour tuning!

Thanks for the help!

Baer383 · 07-24-2013, 06:31 PM

I am getting ready to install my system in my 2013 Nismo and I took the door Molex connector apart and mine is the same as is was on my 2010 sport/touring.

bigaudiofanat · 07-24-2013, 06:41 PM

Quote:

Originally Posted by Baer383

I am getting ready to install my system in my 2013 Nismo and I took the door Molex connector apart and mine is the same as is was on my 2010 sport/touring.

Must of been right before they switched over. Or the OP's could have an extra add on that takes up that blank.Time will tell.

06-17-2013, 10:11 PM	#4 (permalink)
bigaudiofanat Car Audio Installer Join Date: Jun 2009 Location: Magnolia DE Posts: 8,342 Drives: 2012 Infiniti G37x Rep Power: 852	Is this a convertible? I know they use that blank. Pull the rubber back and see if there are wires in all the slots of the green molex location. Also no need for 12 gauge man, go with 16 gauge way easier and you can still run plenty of power through it. MX52Z likes this. __________________ Need help with car audio or electronics? Let me know!! Need Help Let Me Know Direct email address reimermatt@gmail.com Owner of: Dynamic Mobile Audio Follow me below https://www.facebook.com/Dynamicmobileaudio/

07-04-2013, 02:35 PM	#8 (permalink)
killerb87 Base Member Join Date: Jun 2013 Location: plymouth meeting Posts: 11 Drives: 2013 sport Rep Power: 11	I have a 2013 sport. I used the rubber grommet behind the molex connector. Then just ran the wire through the door boot and siliconed both ends. worked great for me. Last edited by killerb87; 07-05-2013 at 04:25 AM.

07-04-2013, 03:45 PM	#9 (permalink)
bigaudiofanat Car Audio Installer Join Date: Jun 2009 Location: Magnolia DE Posts: 8,342 Drives: 2012 Infiniti G37x Rep Power: 852	I will have my first 2013 z install this coming week I will research and get back what I find. __________________ Need help with car audio or electronics? Let me know!! Need Help Let Me Know Direct email address reimermatt@gmail.com Owner of: Dynamic Mobile Audio Follow me below https://www.facebook.com/Dynamicmobileaudio/

07-05-2013, 04:40 AM	#10 (permalink)
Rectorna Base Member Join Date: Feb 2012 Location: Virginia tech Posts: 69 Drives: 2013 PW 370z Sport Rep Power: 13	I have been trying to find molex pins. Look forward to seeing what you end up doing! __________________ Cazper 2013 PW 370z 6MT Sport Fast Intentions l Swifts l Stillen \| Z1 l RJM l SPC l Focal l Audison l JL l LEDs l 20% Tint \| Vinyl l PlastiDip l OptiCoat

07-13-2013, 08:15 PM	#13 (permalink)
Rectorna Base Member Join Date: Feb 2012 Location: Virginia tech Posts: 69 Drives: 2013 PW 370z Sport Rep Power: 13	Well just finished up the install. Seems I left my Bit Ten D setup CD in my old car when I traded it in so I am trying to find the downloads right now. Could not find molex pins so ended up just dremeling a hole big enough for the speaker wire. Thanks for the suggestion to use wire lube really helped out a lot! Now time to spend hour after hour tuning! Thanks for the help! __________________ Cazper 2013 PW 370z 6MT Sport Fast Intentions l Swifts l Stillen \| Z1 l RJM l SPC l Focal l Audison l JL l LEDs l 20% Tint \| Vinyl l PlastiDip l OptiCoat

06-17-2013, 05:15 PM	#2 (permalink)
fuct A True Z Fanatic Join Date: May 2009 Location: Sugar Land Posts: 3,692 Drives: 97' Ranger :) Rep Power: 23	looks different than i remember my 2010 piece looking..

07-07-2013, 05:11 PM	#11 (permalink)
zoomzoom Base Member Join Date: Jul 2013 Location: the Lou Posts: 2 Drives: 2013 370z Sport M6 Rep Power: 11	I just completed a speaker install on a 2013 sport version. Lots of the molex connector has no pins or wires in it which I was able to Dremel through. Its easiest to see what's going on if you unclip the cover on the molex connector and slip off the rubber boot to get to the connector back and wires.

07-24-2013, 06:31 PM	#14 (permalink)
Baer383 A True Z Fanatic Join Date: Aug 2010 Location: Lawrenceville,Ga Posts: 4,293 Drives: My foot up your azz Rep Power: 29	I am getting ready to install my system in my 2013 Nismo and I took the door Molex connector apart and mine is the same as is was on my 2010 sport/touring. __________________ 2013 ZL1 754 rwhp 747 rwtq

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
DIY: Door Panel Removal & Door Speaker Size	jikhead	DIY Section (Do-It-Yourself)	46	07-16-2016 10:04 PM
Door 370Z - 2011 Question?	patchenkou	Exterior & Interior	0	10-10-2011 03:01 PM
Right Door for 370z	Z Monster	Wanted	0	03-12-2011 11:48 AM
370Z gas cap door problems	freddiebear	Exterior & Interior	42	05-15-2010 09:31 AM
Molex Removal?	SlikNik	Audio & Video	8	10-16-2009 05:21 AM