Just want more bass for Bose

pfdaxe · 01-29-2013, 05:46 PM

Quote:

Originally Posted by bigaudiofanat

The front outputs do not carry a full range signal, the best way is to tap into the low level inputs going into the amp, this way you will have a full range signal to do whatever with.

If your going to amp your new speakers step up to either the DXI's from polk or alpine type R's

I only have the RCA inputs going into my amp from the bass output of the LOC, or are you talking about the wires from the HU going into the Bose amp?

Good call on the speakers. I really like the Polk DXi6500's and they're not much more
.
.
.

bigaudiofanat · 01-30-2013, 07:49 AM

Quote:

Originally Posted by pfdaxe

I only have the RCA inputs going into my amp from the bass output of the LOC, or are you talking about the wires from the HU going into the Bose amp?

Good call on the speakers. I really like the Polk DXi6500's and they're not much more
.
.
.

If you tap into the speaker level outputs of the bose amp, you will only get highs or lows depending on which set you tap into. The reason is the bose amp splits the signal before going out to the speakers.

So instead of trying to sum multiple signals, tap into the low level signal going into the bose amp. This will give you a full signal with everything from highs to lows.

pfdaxe · 01-30-2013, 09:33 AM

Quote:

Originally Posted by bigaudiofanat

If you tap into the speaker level outputs of the bose amp, you will only get highs or lows depending on which set you tap into. The reason is the bose amp splits the signal before going out to the speakers.

So instead of trying to sum multiple signals, tap into the low level signal going into the bose amp. This will give you a full signal with everything from highs to lows.

Thanks Matt....as usual

So basically I can disconnect the wires from the bass output of the Bose that I tapped that I have going to the LOC (for sub amp) and replace them on the LOC with the low levels that would be going into the Bose and this will be good for both amps (high & lows)? Then I can completely remove the Bose amp? I wasn't sure if the frequency limiting was at the HU or the Bose amp.
.
.

bigaudiofanat · 01-30-2013, 04:54 PM

Quote:

Originally Posted by pfdaxe

Thanks Matt....as usual

So basically I can disconnect the wires from the bass output of the Bose that I tapped that I have going to the LOC (for sub amp) and replace them on the LOC with the low levels that would be going into the Bose and this will be good for both amps (high & lows)? Then I can completely remove the Bose amp? I wasn't sure if the frequency limiting was at the HU or the Bose amp.
.
.

Yes you can just use the low level full signal, I am not sure about removing the bose amp as I think some things go through it such as volume and a few steering wheel controls (BT phone)

pfdaxe · 01-30-2013, 07:43 PM

Quote:

Originally Posted by bigaudiofanat

Yes you can just use the low level full signal, I am not sure about removing the bose amp as I think some things go through it such as volume and a few steering wheel controls (BT phone)

Matt...you know this was coming...ha...ha...

:

I haven't looked at the wiring diagram yet, so do you know off hand which low level wires going into the Bose amp to connect to the L & R (+ & -) inputs on the LOC?

PS: I think I'm going to go ahead and order the Polk Audio DXi6500 and FOSGATE P400-2 to power them along with a set of base speaker mounts and Zenclosure spacers. Should finish it off...

pfdaxe · 02-08-2013, 12:06 PM

Quote:

Originally Posted by bigaudiofanat

Yes you can just use the low level full signal, I am not sure about removing the bose amp as I think some things go through it such as volume and a few steering wheel controls (BT phone)

I looked at the wiring diagram, and I might just be able to remove the amp. I saw that the Nav voice and BT go from the HU to the front speakers. So, if I'm snipping the front speaker wires before the Bose amp and connect to my LOC like planned, then I'm hoping the Nav voice (which I don't use) and BT will continue to the speakers. Unless for some reason they are processed at the Bose amp. I didn't see anything else going through the Bose amp.

I received my Polk Audio components and Fosgate amp along with an 0 gauge amp kit, distribution block (for the 2 amps) and some new 12 gauge speaker wire. Nissan just called to notify me that my speaker brackets are in. Now I know what I'll be doing this weekend

.
.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Can you get decent bass without a SUB?	papashango	Audio & Video	31	11-06-2013 05:09 PM
Best components for mid Bass.	Juleous	Audio & Video	27	02-18-2011 02:30 PM
Adding more bass to Bose System??????	BenZ	Audio & Video	1	05-22-2010 11:22 PM
My plan for some bass...	ZforMe	Audio & Video	17	05-12-2010 01:33 AM
Upgrade Volume and Bass with Bose/Nav system?	raps101	Nissan 370Z General Discussions	0	08-10-2009 04:29 PM