This just worked for me with a Pioneer AVH-X2700BS in an 2009 Base. Had to manually program using the instructions above, but now works like a charm

bigaudiofanat knowz how to work these. ask him for advise if it dont work.

i got a aswc in my honda fit. it was literally wire up 2 wires and the rest pnp :D

Just finished installing in mine.

2009 Touring Bose Non-Nav.

Pin 6 and 16 exactly as the document says:

http://contentdocs.installernet.com/...icle/11879.pdf

Make sure to ground pin 15 of your harness. Follow the manual setup instructions - it worked for me. PM me if you need help.

Rich

Thanks to all the great info in this thread, took me awhile but finally got my AWSC-1 working almost completely. The only thing I can't get programed properly is the phone buttons, won't register when I program.

The Metra kit for the 370z (70-7552) should really be fixed, missing so many wires including the AWSC-1 wiring and ground. For some reason my new JVC stereo was working without it being properly grounded ;), fixed that and grounded the AWSC-1 to the chassis.

Also, the AWSC-1 didn't detect my stereo properly, said it was a Alpine, this is my second attempt at installing a AWSC, first time was a PITA as well.

Happy I got it working at least, info here was a big help.

HELP!!!! I've been at this for over a day and can't get the AWSC-1 to work with my new JVC receiver in my 2013 Z. The original audio was the base version.

The AWSC-1 won't auto-program, and when I manually do it, it goes thru the cycle (my solid lights are green) but in the end it just gives me 5 quick red blinks saying that it knows I have a JVC, but NONE of the steering wheel controls work. I tried the advice of one post that said to eliminate the last 'down volume ' step, but no go. I also read the posts saying that Axxess has 2 sets of directions for these cars so I reversed the red/gray and blue/grey connections and still nothing works. Anyone know whats going wrong?

OK- so I grabbed a beer and that helped me think a bit more clearly. Comparing all of the paperwork I collected during this marathon I found that there are some conflicting details in the Axxess directions. I sorted them out and NOW EVERYTHING WORKS.

For those interested: one Axxess note says to reset the unit by holding the reset for 2-10 seconds to get to a fast blinking red LED. At 8 seconds my unit goes to a slow blink which is the manual program mode which I could not get to work. Holding the reset for only THREE seconds and then releasing it while the LED is dark puts the unit into the fast blink autoprogram mode. When I did this and then held down the up volume button, the programming went well but the unit would control the volume only.

Based on some suggestions I earlier had reversed the red/grey and blue/gray wires so I now reverted back to my original pairings and tried the autoprogram again ---- now EVERYTHING WORKS.

Hopefully this will help others avoid the time sink I ran into.

Ok.. So I have a question.. Where do I ground my aftermarket stereo?? I've been getting some interference with the radio.. I'm guessing it's because I didn't find where to ground it?? Please help

Ground to chassis, find a spot with a screw and tighten the ground wire there, I used 2 different spots for my radio / awsc-1 install.

Welp, back to the drawing board, firmware update on my JVC deck messed up the ASWC-1, can't get it working again for some reason.

So I need some help

I have a clarion nx702 and the aswc.
My wiring is pink to red/gray.
And blue to blue/gray.
Grounded to a head unit bolt.
And red to red.
And the 3.5mm male to female of head unit

The programming unit has power and the LEDs function but I'm having an issue programming.

I can enter the auto programming mode and it will perform this process.

-rapid blinking after reset,
-then hold Vol up until slow blink begins
-then I get my 7 green blinks (which all appear to be short blinks)
-then I get my 3 red blinks indicating a clarion head unit.
-then I get a slow red blink green blink red blink green blink continuously.

I do not see a slow red blink / slow green blink continuous in the troubleshooting guide.

When I try the manual programming mode, when I hold Vol+ to start the first programming, it never goes solid, it will simply go slow red blink slow green blink continuous. I don't know what this code means and am therefor lost.

Any help you could provide would be phenomenal.

Thanks,

KBC

Will this work with a pioneer avh-p6300bt?

Yes it will

Will the ASWC-1 work with the Pioneer AVIC-6000NEX?

Can I throw out an alternative to the ASWC? Maestro SW. You program it online according to whatever headunit and you can program every button (can program each button to have two functions also.)

Anybody else have thermal issues with these? I just installed my ASWC last week and everything works fine at room temp but not when it gets hot.

Btw, I had to call tech support multiple times to get mine programmed. They're absolutely worthless and they got an attitude with me :shakes head: - just thought I'd throw that out there...

Anyways, the ASWC won't work when I first get off work and my Z has been sitting in the hot parking lot/sun all day. But after I turn on the AC and get about half way home it will start working again. I live in Ohio, so I wouldn't think that this should be an issue since there are plenty of ASWC users out west where it gets a lot hotter there then it does here. Any thoughts?

This should help some people

what's the difference between the aswc and the aswc-1? thanks

This worked for me. Took several times to work as the last step never fully worked. Not sure what I did differently to make it finally worked but I'm happy it did.

I appreciate the help!

Bluetooth

Sent from my SAMSUNG-SM-G870A using Tapatalk

**** ya! 😁😁

Lol glad I could help by making that.

just setup the ASWC in my 370z with an android head unit.

had to do the full manual setup, but everything works including the phone buttons without modifying the wiring in the trunk area.

thank you very much!

THANK YOU for posting this.. I spent the better part of a day messing around with this on my 2014. Not only were the pins wrong in the instructions, so were the steps to program. Great video!

I got mine working in April after working thru problems with my head unit finding it (Parrot Asteroid Smart). Tried auto program, then manual and would get the correct number of flashes, but the HU wouldn't see it. Called Axxess and after convincing them it was current version of firmware, hooked up correctly per their instructions, etc. etc. they said I should try switching the 2 steering wheel control wires (as someone had mentioned in an earlier post). Rather than resolder, I switched the pins after which it auto programmed and HU found it. Yeah!

Everything is great until this weekend when it was parked in the sun on a 90+ degree day. None of my buttons worked when I got in the car, but remembered Loges post about thermal issues. Unfortunately, tried them several times during the 3 hour drive home, but no joy. Guess I get to pull the console apart once more. :thumbsdown::ugh:

Kind of wish I had tried the Maestro...

Just got finished with this on the weekend. This thread was a BIG help.

After I was ready to tear the damned thing out I read the head unit manual and found that my Sony MEX-XB100BT needed to have the external remote output enabled. Should've read the head unit instructions first.

That my friend is the STUPIDEST setting I've ever seen in my 12+ years of installation. I hate that setting.

Did this install to my z today. This is perfect instruction video ! Thanks!

ASWC-1 Connector - AX-NIS32BT
 

I know I'm very late in this discussion but I'm putting in a new Pioneer head unit in my car and bought the ASWC-1 from Crutchfield. After reading all of the documentation I found this note on bypassing the 370Z Bluetooth controller. You can do this manually but Axxess makes a plug that does the bypass for you so the head unit and the SWC work together. It's the AX-NIS32BT and it is $12.99.