i can get a close up for you some time today. just of the hub?

that would be great... just a couple shots all around the lug/hub area in the center of the wheel. i would like to see the opening where the centercap goes etc and see what i can determine before my wheels arrive. unfortunately without getting a precise inside diameter of the SLs hub, i cant really bother starting the CAD work.

just a heads up. im rockin a 20mm spacer with my 10.5 +12 te's +12 up front too. just dont expect a huge tire

thanks spec jay for the heads up. im not going to run spacers. i was going to but not anymore. im just goin to get the camber kit from lou

hope this helps phunk, not the best pix

front
http://img.photobucket.com/albums/v2...n/IMG_3244.jpg
http://img.photobucket.com/albums/v2...n/IMG_3249.jpg
http://img.photobucket.com/albums/v2...n/IMG_3246.jpg

rear
http://img.photobucket.com/albums/v2...n/IMG_3250.jpg
http://img.photobucket.com/albums/v2...n/IMG_3251.jpg


i know i need to paint the inside black, lol. just been lazy

you sure? haha
this is with the 20mm and -3 camber in the rear
http://img.photobucket.com/albums/v1...g?t=1292108773
im going back down to a 15mm so i can go wider with less camber

want to send me your 20mm so i can try them out :tup:

j/k

looks good though, i still dont think im going to run spacers. im just going to do the camber kit and go from there. i do want to put wider tires on as well

i guess you might be ok since you aren't running the +12 up front. sure makes me nervous about going with a 255 hahah

you will probably rub with a 255 up front no? i have a little room with the +22 up front and a 245/40. fully lock it rubs just a tiny little bit with my setup

i plan on rolling the lip flat on the front. im also running 5 series smaller. i only rub the fender liner.

thanks for the pictures!!

is that lip i see back in there, the edge of a hub centric ring?

NP! Yup that is the hub centric ring

excellent... since it is exposed on the inside of the hub opening, that means it will be no trouble to fit a one-piece centercap / hub ring in there!

Just in case you decide you want to try spacers :tup:

http://www.the370z.com/parts-sale-pr...acers-f-s.html

thanks holliday, im just going to fix my alignment though. and im going to be raising the car a little bit. we went on a canyon run and i was scraping everything, including "ant poop" as my fiance stated. i need to stiffen the coils up a bit and get some sways. i had some body roll. my front lip hit something as well and chipped the finish on it. it didnt crack the lip though thank god, just took the finish off which is fixable

Raise it we can tune the suspension then worry about sways. :tup:
Good times! Man that was a challenge on the way back down and those damn cow crossings and you having to cross them so slow...

haha ya those cow crossings suck. how much do you think we should raise it? maybe a bit lower than yours? i got the video, and its uploading. the video going up wasnt as good as the video coming down

I was reading your guys discussion...

Am I going to have problems with these rims and my tires? I'm running a 255/40 up front. I got the same offsets and sizing as Ilive2win.

I might actually bring the front up on mine this week maybe about a quarter inch, I would suggest a 2 finger gap around all four corners, that's where my rear is at and my front is at about 1.5 fingers. Maybe just bring it up a little lower the Charles or right around there, it is beauty vs function and well you want to drive... Haha

Sounds good, looking forward to the videos in either direction... Haha!

you should be fine, it may rub a little if you are lowered a lot but you should be fine. what tires are you running?. i guess the nt05's run a little bit wider than others and im super low and it only rubs on canyon runs and lock to lock lol

i have 265 going up in front... better not rub!

what tires are you guys going to run?

I got the Hankook V12s. 255 up front 285 in back.

you shouldnt have any problem running the v12's in that size. there should be no/minimum rubbing and wouldnt worry about it. im just rubbing because im so low, which i will be fixing this week

Guess who else is getting SL's after seeing them on your car?
:happydance:

haha, what happen to getting ssr's?

Me! but I ordered mine back in August. lol. They're finally arriving on Thursday :excited: ... but I wont be installing them until spring because my car is in winter storage now :(

Well an opportunity presented itself and I can get a set by the end of this month! I don't want to wait haha...and I got lucky.

Thinking about getting the Shine Auto kit too. Sunline is too expensive for something I will scratch haha.

got my FRONT SLs today... waiting for my 19x11 rears still!

What size rear tires you going with ?? Like a 315 or wider maybe ???

Nice car but man, the rear is hella sunk... for rims that $$$ I'd want them to fit perfect without spacers.

Mine are on their way. I got a tracking number finally. Apparently they will be here the 24th. Great Xmas gift I guess :tup:

awesome ride looks sick. where did u get the body kit????

Love the look

thanks! i got it from lou @ amplified motorsport. he's a vendor on here