Nissan 370Z Forum - Search Results

		Nissan 370Z Forum > Search Forums
Search Results

Showing results 1 to 12 of 12
Search took 0.00 seconds. Search: Posts Made By: Knio

Forum: Tuning

12-14-2018, 01:02 AM

Replies: 133

370Z CAN Bus Proprietary PID's

Views: 48,127

Posted By Knio

The signals for blinkers, doors, and ebrake...

The signals for blinkers, doors, and ebrake should be in the spreadsheet under the BCM.

Unfortunately I don’t think you can control anything over CAN because the input switches go directly into...

Forum: Tuning

12-12-2018, 01:58 AM

Replies: 133

370Z CAN Bus Proprietary PID's

Views: 48,127

Posted By Knio

Yup, the base model does not have the gear...

Yup, the base model does not have the gear position sensor. You could always do what my motorbike does and compute the ratio between the RPM and rear wheel speeds to look up the gear. Only works when...

Forum: Tuning

10-11-2018, 09:53 AM

Replies: 133

370Z CAN Bus Proprietary PID's

Views: 48,127

Posted By Knio

You would get a warning if they were missing. ...

You would get a warning if they were missing.

Are you driving when reading this? The sensors go to sleep and only start sending values after a minute or so of > some minimum speed. One of the...

Forum: Tuning

06-11-2018, 11:16 AM

Replies: 133

370Z CAN Bus Proprietary PID's

Views: 48,127

Posted By Knio

Brad's dropbox sheet is probably the best...

Brad's dropbox sheet is probably the best documentation. TPMS is CAN ID 385

Forum: Tuning

05-31-2018, 10:03 PM

Replies: 133

370Z CAN Bus Proprietary PID's

Views: 48,127

Posted By Knio

I haven't heard of any further progress on this...

I haven't heard of any further progress on this in a long time, but I think we have a pretty good understanding of the CAN architecture and signals built up. Is there anything specific that you're...

Forum: Tuning

11-07-2015, 11:31 PM

Replies: 133

370Z CAN Bus Proprietary PID's

Views: 48,127

Posted By Knio

Found this in the service manual, the Bosch...

Found this in the service manual, the Bosch sensor isn't hooked up to the main CANbus, and is instead relayed through the ABS controller, this probably explains why the signals don't match up exactly...

Forum: Tuning

11-05-2015, 12:36 AM

Replies: 133

370Z CAN Bus Proprietary PID's

Views: 48,127

Posted By Knio

0x245 F=64 when stability control activates

0x245 F=64 when stability control activates

Forum: Tuning

10-30-2015, 12:51 AM

Replies: 133

370Z CAN Bus Proprietary PID's

Views: 48,127

Posted By Knio

I had these same issues (though with a windows...

I had these same issues (though with a windows tablet) and think I finally solved them. (incredibly annoying)

1) I found an OTG USB hub that takes external power, and powers both the tablet +...

Forum: Tuning

10-04-2015, 09:27 PM

Replies: 133

370Z CAN Bus Proprietary PID's

Views: 48,127

Posted By Knio

I just confirmed with an external 6axis...

I just confirmed with an external 6axis accelerometer/gyro going through some hard turns:

CAN ID 0x292 is the Bosch yaw rate sensor:...

Forum: Tuning

09-16-2015, 11:27 PM

Replies: 133

370Z CAN Bus Proprietary PID's

Views: 48,127

Posted By Knio

I'd help making a better python obdII library...

I'd help making a better python obdII library (the ones out there kinda suck) that could have all the extended Nissan PIDs.

I already released a GPS library that I made for my project...

Forum: Tuning

09-15-2015, 12:57 AM

Replies: 133

370Z CAN Bus Proprietary PID's

Views: 48,127

Posted By Knio

I've been watching your blog since we talked a...

I've been watching your blog since we talked a few years ago, I was really happy when you found the odometer :)

Load testing my new hardware today:
...

Forum: Tuning

09-13-2015, 10:09 PM

Replies: 133

370Z CAN Bus Proprietary PID's

Views: 48,127

Posted By Knio

I never noticed this thread, my project is one...

I never noticed this thread, my project is one referenced in OP.

Currently I'm *still* working on getting a windows tablet installed in the cubby and haven't had time to write any code for a long...

Showing results 1 to 12 of 12

Forum Jump

All times are GMT -5. The time now is 05:30 PM.