Nissan 370Z Forum - Search Results

		Nissan 370Z Forum > Search Forums
Search Results

Showing results 1 to 11 of 11
Search took 0.00 seconds. Search: Posts Made By: redondoaveb

Forum: Forced Induction

11-06-2019, 06:28 PM

Replies: 43

Pulleys

Views: 8,520

Posted By redondoaveb

As mentioned by"Z"en, you won't need spacers...

As mentioned by"Z"en, you won't need spacers unless you change the jackshaft pulley, sc side. Also, the idler wasn't a tight fit at all. No issues using the 3" idler.

Forum: Forced Induction

11-06-2019, 06:24 PM

Replies: 43

Pulleys

Views: 8,520

Posted By redondoaveb

Good point. It's too bad Vortech won't do ceramic...

Good point. It's too bad Vortech won't do ceramic bearings in the V3 though.

Forum: Forced Induction

11-05-2019, 09:08 AM

Replies: 43

Pulleys

Views: 8,520

Posted By redondoaveb

I used the 9lb and a 2.85 supercharger pulley to...

I used the 9lb and a 2.85 supercharger pulley to get to 13 psi (12.86 to be exact). You'll have to go to a 3.00 idler on the supercharger side if you go with the 2.85.

Forum: Forced Induction

11-04-2019, 10:53 AM

Replies: 43

Pulleys

Views: 8,520

Posted By redondoaveb

If 91 is the only fuel you're going to run then...

If 91 is the only fuel you're going to run then the wastegate wouldn't be needed. You can run around 13 psi on 91 before knock. If you plan on boosting above that level by using a higher octane fuel...

Forum: Forced Induction

11-04-2019, 09:13 AM

Replies: 43

Pulleys

Views: 8,520

Posted By redondoaveb

Actually, if you plan to spin the V3 faster than...

Actually, if you plan to spin the V3 faster than it's max rpm of 52000 then you should get the 928 ceramic bearings. The Si impeller is just fine. Mine actually started making boost sooner than the...

Forum: Forced Induction

11-02-2019, 01:07 PM

Replies: 43

Pulleys

Views: 8,520

Posted By redondoaveb

The spacers you can get from 928 for less than...

The spacers you can get from 928 for less than $30.00. Those have nothing to do with boost levels as he was asking about.

My car made over 10 psi with the Si sc, 9lb pulley and stock filter....

Forum: Forced Induction

11-02-2019, 11:35 AM

Replies: 43

Pulleys

Views: 8,520

Posted By redondoaveb

My car with the 928 super vortech, 9lb pulley,...

My car with the 928 super vortech, 9lb pulley, 3.47 jackshaft pulley sc side and 3.00 sc pulley made 16.4 psi.

With the 928 impeller and the 9lb pulley I bet you see closer to 11 psi. Also, if I...

Forum: Forced Induction

10-27-2017, 12:09 AM

Replies: 43

Pulleys

Views: 8,520

Posted By redondoaveb

Since I already have the 2.87 supercharger pulley...

Since I already have the 2.87 supercharger pulley I went ahead and ordered the larger idler pulley that tbatt showed. Since my sc isn't installed yet I don't know if I'll have the same clearance...

Forum: Forced Induction

10-26-2017, 01:39 PM

Replies: 43

Pulleys

Views: 8,520

Posted By redondoaveb

You're right, I was (but not now, I hope)...

You're right, I was (but not now, I hope) confused :o So, on the supercharger side you have a jackshaft pulley, an idler pulley and the supercharger pulley. Correct? Thanks for the Gates info.

Forum: Forced Induction

10-25-2017, 07:38 PM

Replies: 43

Pulleys

Views: 8,520

Posted By redondoaveb

I purchased a 9lb jackshaft pulley and I also...

I purchased a 9lb jackshaft pulley and I also purchased a (if I'm not making the power that I want) 2.87 suoercharger pulley. Of course I have your kit. Supercharger is being installed this week and...

Forum: Forced Induction

10-24-2017, 12:30 PM

Replies: 43

Pulleys

Views: 8,520

Posted By redondoaveb

Even with your kit? Could you install the old sc...

Even with your kit? Could you install the old sc pulley as the idler pulley or is it not compatible and/or big enough?

Showing results 1 to 11 of 11

Forum Jump

All times are GMT -5. The time now is 10:58 PM.