Nissan 370Z Forum

Nissan 370Z Forum (http://www.the370z.com/)
-   Nissan 370Z General Discussions (http://www.the370z.com/nissan-370z-general-discussions/)
-   -   HF jackstand recall (http://www.the370z.com/nissan-370z-general-discussions/133868-hf-jackstand-recall.html)

JARblue 05-20-2020 09:56 AM

Quote:

Originally Posted by Zoren 370 (Post 3935731)
When the Z broke down left it up on the same jacks for months!

And sometimes I’ll crawl underneath just to take pictures!

Damn I could have ended like a squeezed empanada!

My Z has been up on HF jack stands for over a year. I put a floor jack under the car for support and was careful not to bump the car when I crawled underneath to check the model number. Even though mine weren't recalled, I don't trust them now lol

SouthArk370Z 05-20-2020 10:32 AM

I didn't get my stands from HF but checked them anyway. Brands and model numbers are different. It gave me a good excuse to give them a thorough inspection. I discovered that I hadn't done the retaining tab on one of them properly and the post will fall out if you turn the stand upside down - will correct that before I use again.

Does anyone know what part(s) are causing the problem? As simple as a jackstand is, there's not too much that can go wrong.

JARblue 05-20-2020 12:25 PM

Check the engagement on the pawl per BettyZ (Post #6).

FWIW, I never engage the retaining tab. I find it's easier to stack them for storage, which requires removing the inserts. Easy enough to avoid turning them upside down.

SouthArk370Z 05-20-2020 03:05 PM

Quote:

Originally Posted by JARblue (Post 3935756)
Check the engagement on the pawl per BettyZ (Post #6).

Ah. I missed that on my first read. Thanks.

Quote:

Originally Posted by JARblue (Post 3935756)
FWIW, I never engage the retaining tab. I find it's easier to stack them for storage, which requires removing the inserts. Easy enough to avoid turning them upside down.

Not something I'm really worried about (it doesn't affect the functioning of the stand) but it might save some sore toes down the line.

cv129 05-20-2020 06:51 PM

I've never engaged that tab either....actually I've never paid attention to that tab until reading JAR and SouthArk's comments....I just always assumed that I shouldn't hold it upside down lol.

:iamwithstupid: #footinmymouth #selfincriminate #learnsomethingnew

I never raise the inserts above the bottom height, I've never felt comfortable conceptually. Besides, my 6 tons (HF) is quite tall to start with, and the 3 tons (Craftsman) give ample of height for the simple things I do.

I'll probably go for more reputable units :usa:, or at least something rated ridiculously more than my car, like 2 pairs of 12 tons :p, if I have to be entirely under the car for a long time.

danegrey 05-20-2020 06:59 PM

Well I got two that are in the recall, so I will take them back and get my gift card, thanks for the post, would not even have thought about it...

Z_ealot 05-20-2020 07:24 PM

No jack stands from HF here, just good old 6 ton craftsman :)

Zoren 370 05-21-2020 02:08 AM

Is the gift card only good at HF for purchase?

Darn it when I needed the stands to hold my RCF up in the air to ceramic coat the wheels!

Now Im left with a gift card!!!

Do strippers accepts gift cards for lap dance?

MZ DAIZY 05-21-2020 05:46 AM

Only Chinese strippers.

Zoren 370 05-21-2020 07:11 AM

Quote:

Originally Posted by MZ DAIZY (Post 3935936)
Only Chinese strippers.

Ok I rather be squeezed by my car due to jack stand failure!

Rather than loosing my personal elevating rod to covid19 from a Chinese!

ZoomZ 05-21-2020 11:56 AM

Quote:

Originally Posted by BettyZ (Post 3935570)
If anyone here uses HF jackstands, an urgent recall is out. About damn time, mine collapsed on me two-ish years ago.

https://www.roadandtrack.com/car-cul...of-collapsing/

Sent from my SM-G955U using Tapatalk

Pictures?


All times are GMT -5. The time now is 12:05 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2