Thanks Mike:tiphat:

If you look close I painted the area that goes under the cowl black so you don't see it and added new foam gasket on each side by the cowl like Nissan does.:tup:

dude where u got the spoiler from? looks nice

Hey nice ride. Were your dyno numbers performed with the 20" Venacis?

I love the strut bar. Looks great Frank!

I got it from Rick at VIP Status.

No I had a set of 18's on the 20's would have robbed a little more power.

Thanks Will,I welded in some metal like the Nismo ones and Mike put on a satin gray powercoat, I like it allot.:tup:

Frank, do you have any step by step pics of the strut bar creation?

No I just took a pic of a Nismo strut bar and kind of measured by eye where the struts should be and welded them in then ground it down and metal finished it and sent it to Mike for powder coating.

The only thing I messed up on is the Nismo struts are a little wider than the ones I installed.

The strut it self is 2 pieces of metal one on top of the other I just welded up the seam and ground it to fit.

I got a couple of pics of my Shine auto front lip & rear add on's plus stillen rocker's,to cold to put them in I should get a nice day here soon the winters in Georgia are pretty mild.

http://i832.photobucket.com/albums/z...3/IMG_0176.jpg
http://i832.photobucket.com/albums/z...3/IMG_0173.jpg
http://i832.photobucket.com/albums/z...3/IMG_0180.jpg
http://i832.photobucket.com/albums/z...3/IMG_0179.jpg
http://i832.photobucket.com/albums/z...3/IMG_0177.jpg

Sweet Frank. Can't wait to see them on the car. I wish someone would make the rear spats but where they connect all the way across the rear section.

Here are some pics ,I took the rockers back off to add more pearl they are way to light compared to the quarter panel.
http://i832.photobucket.com/albums/z...3/IMG_0181.jpg
http://i832.photobucket.com/albums/z...3/IMG_0185.jpg
http://i832.photobucket.com/albums/z...3/IMG_0182.jpg
http://i832.photobucket.com/albums/z...3/IMG_0183.jpg


I even two toned the paint that goes into the wheel well area so it looks OE
http://i832.photobucket.com/albums/z...3/IMG_0180.jpg
http://i832.photobucket.com/albums/z...3/IMG_0188.jpg
http://i832.photobucket.com/albums/z...3/IMG_0187.jpg
http://i832.photobucket.com/albums/z...3/IMG_0189.jpg

:tup: nice work

Looking really good, meaner now with those add ons. And you're right, you gave it a nice OEM touch

Looks good! I of course did not think you were going to paint it exactly the same as I did since we go to same meets all the time! This is a surprise!

I didn't' want to two tone it like that but it was a bitch to tape it up to have more white vs black ,plus I went with Stillen rocker vs Shine auto.

Looks great Frank. Can't wait to see it in person. How much lower is the lip in the middle? Can't wait to order mine I'm CF.

Dude my car is so low that I can't get it out of my driveway,I will have to raise it up to get it out.:ugh2:

The lip is as low as the bottom of the chin spoiler.

Are you lower then me? I scrape all the time! It's a way of life for me.

Spohn, You too?? Might be time for a change! :p

I have to raise my car.:ugh2:

I raised her up a whole 3mm for winter! Still hovering around 3" clearance front lip.

I don't have 3" of ground clearance :shakes head:

This sucks my car looks good and I have to repaint the rocker covers and can't drive it around,I wanted to raise it in the spring so I guess I will be doing it sooner than later.

Yea I know and it's coming. My eyes is on this kit. But I know of another company that's creating a new kit come spring. So I'm some what holding out for that.

It must be your wheel diameter. My gap above my tires seems smaller then yours. That's got to be it.

I have the same size wheel & tire you have,the gap above the tire is about .75 inch.

20x9.5 +17 255/30/20
20x11 +5 305/25/20

I have just short of .5 inch gap. Then maybe the Shine lip dimensions are truly different from the Sunline lip. Strange

When I put the lip on I kind of let it fall where it wanted to then adjusted it even from left to right and that's it.

I tried to push it up higher but like I said it kind of wanted to sit where it is.
it looks good it was a p.i.a. to put it on being it was very tight,it will be neat to see yours next to mine.

Have a good new year Kev:hello:

Thanks guys:tup:

I got the rocker covers repainted now they look good ,don't have any pics of the new paint maybe when it warms up alittle.:tiphat:

Here are some finished pics
http://i832.photobucket.com/albums/z...3/IMG_0207.jpg
http://i832.photobucket.com/albums/z...3/IMG_0201.jpg
http://i832.photobucket.com/albums/z...3/IMG_0205.jpg
All gaps between the body kit and bumper were sealed and smooth
http://i832.photobucket.com/albums/z...3/IMG_0202.jpg
http://i832.photobucket.com/albums/z...3/IMG_0208.jpg
http://i832.photobucket.com/albums/z...3/IMG_0210.jpg
http://i832.photobucket.com/albums/z...3/IMG_0209.jpg

thats just a lil sick frank... :p looking good man!

Looks good. Now I have to change my interior also though!! Cut it out!! :p

Kit looks good!

Thanks :hello:
It is a Shine auto front lip,and rear add on's,w/Stillen rockers
I like it I think it came out good.:tup:

Pure sex

I like the steering wheel bottom. I opted against it but it does look good!

It looks good and does make it easier to get in and out but it's weird when you turn the wheel all the way around.:ugh2:

The lips looks really good. Can't even tell its a add on

Thanks :tiphat:if you look at the pic with the rear add on you can see that I figured out a way fill the gap but yet look molded on.

Excellent work with this showroom PW Z; it looks so good, it makes one want to slap his mamma.

Car looks GOOD Frank!!!