Nissan 370Z Forum
Page 29 of 71 « First 192728 29 303139 Last »
Show 40 post(s) from this thread on one page

Nissan 370Z Forum (http://www.the370z.com/)
-   Member's 370Z Gallery (http://www.the370z.com/members-370z-gallery/)
-   -   Madwi's picture dump and crap (http://www.the370z.com/members-370z-gallery/122773-madwis-picture-dump-crap.html)

madwi 02-13-2019 11:10 PM
Quote:
Originally Posted by old guy (Post 3824832)
Every time y'all do some of these mods ( sway, rotors, brake lines & so on ) I think yeah ok...... but do I want to start down that rabbit hole :rofl2:
It is a pain in the rear end, especially when life demands attention every 20 minutes. :icon17:

Rusty 02-14-2019 07:43 AM
1 Attachment(s)
Quote:
Originally Posted by old guy (Post 3824832)
Every time y'all do some of these mods ( sway, rotors, brake lines & so on ) I think yeah ok...... but do I want to start down that rabbit hole :rofl2:
It depends on what you what to get out of it. Nice looking DD, A fast DD, Track rat, etc. But once you start. Sometimes things go sideways. :rofl2: Then you go down the rabbit.

Hotrodz 02-14-2019 08:51 AM
Quote:
Originally Posted by Rusty (Post 3824890)
It depends on what you what to get out of it. Nice looking DD, A fast DD, Track rat, etc. But once you start. Sometimes things go sideways. :rofl2: Then you go down the rabbit.
The minimum suspension mod requirements to meet this requirement: front sway bar, FUCA, rear camber arms and coilovers. After that we will see you at the bottom of the rabbit hole.:tiphat:

madwi 02-17-2019 04:02 AM
Quote:
Originally Posted by old guy (Post 3824829)
Mad, did you cut the hood and install the vents?
I'll snag some pics today... :eekdance:

madwi 02-17-2019 05:30 AM
https://i.imgur.com/xSdNqrhl.jpg
https://i.imgur.com/ekzRkOMl.jpg
https://i.imgur.com/JFan4b5l.jpg
https://i.imgur.com/QU3qgrul.jpg

madwi 02-17-2019 05:34 AM
Still need to do passenger side. I have a brand new pack of discs for the grinder and I cant find them. I tore everything in the garage and basement apart looking for them. :mad: Will have to see if I can find some locally today.
EW complains about me not letting him help work on the car so I'll have to let him give me a hand when it comes time to riveting the vents in place. :icon17:

jwick 02-17-2019 12:05 PM
Quote:
Originally Posted by madwi (Post 3825771)
Still need to do passenger side. I have a brand new pack of discs for the grinder and I cant find them. I tore everything in the garage and basement apart looking for them. :mad: Will have to see if I can find some locally today.

EW complains about me not letting him help work on the car so I'll have to let him give me a hand when it comes time to riveting the vents in place. :icon17:

I recommend a reamer on those cut edges. I have a cheap one that works wonders. You going to coat the cut edge with something?

madwi 02-17-2019 12:42 PM
Quote:
Originally Posted by jwick (Post 3825836)
I recommend a reamer on those cut edges. I have a cheap one that works wonders. You going to coat the cut edge with something?
I have a sheet metal deburr tool that I will break the edges with. Yes to coating the edges. Not sure what to use. I need to stroll about the paint aisle at the parts store.

jwick 02-17-2019 01:48 PM
Madwi's picture dump and crap
 
Quote:
Originally Posted by madwi (Post 3825853)
I have a sheet metal deburr tool that I will break the edges with. Yes to coating the edges. Not sure what to use. I need to stroll about the paint aisle at the parts store.

You could cold galvanize it. They sell it in a spray can at Home of Pot. I just spray some of it in a disposable cup and brush it on.

Be careful with where you set the cup down. It eats thru a solo plastic cup of you just leave it sitting there.

old guy 02-17-2019 04:21 PM
Mad that looks great ! Is there going to be a center vent? I think it looks good without it. :twocents: :icon14:

Rusty 02-17-2019 06:49 PM
Quote:
Originally Posted by jwick (Post 3825865)
You could cold galvanize it. They sell it in a spray can at Home of Pot. I just spray some of it in a disposable cup and brush it on.

Be careful with where you set the cup down. It eats thru a solo plastic cup of you just leave it sitting there.
That's what I did. :tup:

jwick 02-17-2019 08:09 PM
Madwi's picture dump and crap
 
Quote:
Originally Posted by Rusty (Post 3825919)
That's what I did. :tup:

That’s how we did the rivet holes on the track car when we deleted the sunroof.

madwi 02-18-2019 12:16 AM
Quote:
Originally Posted by old guy (Post 3825890)
Mad that looks great ! Is there going to be a center vent? I think it looks good without it. :twocents: :icon14:
No center vent for me right now. :tup:

madwi 02-21-2019 12:14 PM
Had a few minutes this afternoon and got the holes cut out in the hood.
https://i.imgur.com/4CMjVZKl.jpg
https://i.imgur.com/FveYkPXl.jpg
https://i.imgur.com/XdQIzi3l.jpg

carlitos_370z 02-21-2019 01:25 PM
Damn bro your car looks amazing :drool:


All times are GMT -5. The time now is 06:04 AM.
Page 29 of 71 « First 192728 29 303139 Last »
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2