Unfortunately, the Aimgain and Nismo bumpers are similar, but have slightly different lines. I purchased Wiggins' Aimgain canards to mount on my Nismo bumper and they weren't even close to fitting. I'll be having a bodyshop take care of getting them on.

yeah a friend of mine found a set in japan and had them shipped over and he will be rebuilding them specs in the rear are 19x13 -25 same as wiggles and the front are to be determined still!

im going to borrow a friends of mine to test fit

Gigantic snow plow... It looks almost the same... 😂

its better then spending 3000 total on the aimgain bumper:rofl2:

Or $1500...


Sent from my iPhone using Tapatalk

Well thew front are cut and just tapped on for adjustments, the front bumper is now the biggest project on my hands
http://i100.photobucket.com/albums/m...psc5q7wqhk.jpghttp://i100.photobucket.com/albums/m...psch5i6pof.jpghttp://i100.photobucket.com/albums/m...psytxk0brn.jpghttp://i100.photobucket.com/albums/m...pswqxtszgm.jpg

the night was a success, the lines for the rear are lined up and ready to be cut on both sides, I will be cutting 18-20 mm down from the body line in the rear quarter panelhttp://i100.photobucket.com/albums/m...ps8szfqth9.jpghttp://i100.photobucket.com/albums/m...ps5fezxnka.jpghttp://i100.photobucket.com/albums/m...psd3q69qpi.jpg

Where the rear bumper attaches to the body i will be cutting around it to attempt to keep it as an attachment point

Did a little project i have been procrastination for a while now. dual oil catch cans. http://i100.photobucket.com/albums/m...ps6fmx7djk.jpg

For the DIY'ers out there the picture go in order of my cuts
Cut:1 i cut just bellow where the bumper meets the body to keep the mount for the bumper. as well the top most line was first cut do to the unknown as to where the body met the inner fender well
http://i100.photobucket.com/albums/m...psxvkgf3vb.jpg
Cut 2: i cut an inch or so down just so i can look behind the body to determine where the body met the well.
http://i100.photobucket.com/albums/m...pspaenak18.jpg
Cut 3: i determined the perfect line to follow to cut was the width of electrical tape that is where you will eventually need to cut the well at.
http://i100.photobucket.com/albums/m...pso79wzmox.jpg
Cut 4: not finished in the picture but right above the blue tape is where i will be cutting the well to finish the cutting.
http://i100.photobucket.com/albums/m...ps9kthsvl5.jpg

*tips hat*

Surely you have a DD and you don't quit on this...

Enjoyed the build however short, and I'm in for the finish!

Keep it up!

thanks ma dude and my DD is an 07' audi A3 bagged http://i100.photobucket.com/albums/m...psfqae3vgb.jpg

Wheels specs are final! 19x13 -25 and in front 19x10.5 -23! 7 inch lip in back with -2 degrees of camber

So after contacting both bulletproof and aimgain about the front fitment issuse i have made no progress. they say all i need to do is go to a shop and have them doing it for you. they are stating that when making them they come out longer then they are supposed to. SO if you get the aimgain flares be prepared for this perfect fitment in front. not happy with this 2500 dollar "high quality" product. http://i100.photobucket.com/albums/m...ps4vagdxkx.jpghttp://i100.photobucket.com/albums/m...psoxh1xpb1.jpg