Originally Posted by eastwest2300 (Post 3970025)

:rock::rock::rock::rock:

many people happy, many people :mad:, many people will just have to suck it up duude.

Originally Posted by eastwest2300 (Post 3970064)

saints vs buccaneers.. sunday night football.

who YOU got dude?

Originally Posted by BoneZ (Post 3970068)

You can dew et!

Originally Posted by jwick (Post 3970071)

I’m with Spooler. I don’t see how anybody can be happy. We went into this election knowing the winner would be the worst president we’ve ever had in this country. Truly embarrassing that those two yahoos were the best this country can come up with.

Originally Posted by BoneZ (Post 3970076)

Idunno...

Originally Posted by JLarson (Post 3970050)

That's a big thumbs up from me. We spent the day hiking Gertrudes Nose near Rochester, and drove from there to Ithaca. Tomorrow, Robert H Treman park, Watkins Glen, and possibly Toughahannock falls (courtesy of Lein - thanks for the rec!). Tomorrow night we start looping back through Northern PA. We'll hike around Cherry Springs for a day, and meander slowly home from there. Glad to see you all are doing well!

Originally Posted by redondoaveb (Post 3969857)

So we did a pulley swap and dropped my boost from 19.15 psi @62700 rpm to 15.81 psi @ 56400 rpm. Was hoping to pick up power by bring the blower back into the efficiency range. It lost a little more power and torque.

What's weird is that with my V3 blower, every pulley change I did spun the blower faster (out of it's efficiency range) but it picked up power and torque with every change. With the same pulley set up on the new V2 as I had on the V3, the V3 made more power.

Something isn't making any sense. I don't know if I want to change the intercooler and see what happens, although soho says their intercooler is good for 1000 hp, I researched difference IC cores and the same size core from Bell is rated at 425 hp and one from Vibrant is rated at 600 hp. The shop that built my car is suggesting spraying cold air (nitrogen or nitrous) into the the IC core while on the dyno and see if the hp dramatically rises. Then I would know that the IC is undersized. But the IAT's weren't high anyway.

Attached are 2 dyno sheets, one showing the 19.15 psi run and the 15.81 psi pulley change run. The other one shows my old V3 16.78 psi 679whp run and the V2 19.15 psi 634whp run utilizing the same pulley combo on both blowers.

Originally Posted by DrBacon (Post 3970083)

A restriction I would figure would show up on the top end when you'd be making more boost than previously, you wouldn't be down on power throughout the whole pull when not pushing that much air. Obviously the new supercharger probably takes a bit more power to spin, but you are also building more boost throughout the whole RPM range too which I would imagine should be counteracting that.

I'm not sure if this has been asked but have you had a compression test done?

Originally Posted by redondoaveb (Post 3970086)

I talked to Seb about maybe doing a compression test and he will if I want but he and the shop that built my car both said the motor is acting healthy. There's nothing to indicate that the motor is hurt. I may have him do one and hopefully eliminate that equation.

Originally Posted by redondoaveb (Post 3970086)

I talked to Seb about maybe doing a compression test and he will if I want but he and the shop that built my car both said the motor is acting healthy. There's nothing to indicate that the motor is hurt. I may have him do one and hopefully eliminate that equation.

Originally Posted by DrBacon (Post 3970089)

Yeah with that stillen manifold in the way I know it's not a simple task to do but I think it might be worth trying just to see. I don't know what else would result in such a consistent loss of power across the entire rpm range even when you're making a fair bit more boost.

Keep us updated though, I am genuinely curious.

Originally Posted by Spoiler (Post 3970096)

Just peeking in the window to see who is up. :wtf2:

Originally Posted by jchammond (Post 3970103)

Just watched a short Autox event & was thinking............imagine how many cones that Jar would mow down :rofl2:

Originally Posted by Rusty (Post 3970081)

Try hiking at 8,000 ft. You get a bit winded.

Originally Posted by jchammond (Post 3970107)

:hello: Have a great Monday folks, Spoiler ring the bell for errbody :tiphat:

Originally Posted by jchammond (Post 3970103)

Just watched a short Autox event & was thinking............imagine how many cones that Jar would mow down :rofl2:

Originally Posted by jchammond (Post 3969939)

:tiphat: I don’t have the lock cable for mine; probably need to run a rope or something through the eyelets, but fits very good/snug :tup:

Originally Posted by Leingod (Post 3970120)

Would you like the lock cable from this one when it gets here? I'll never use it

Originally Posted by BettyZ (Post 3970125)

Morning itcheZ. Monday is a real taint-licker.

Originally Posted by Pintsize725 (Post 3970039)

For the race fans:
https://www.apexatxmedia.com/SVRA-COTA-2020/

Spent the weekend trackside for SVRA.

Oh, Hi.