Nissan 370Z Forum

Nissan 370Z Forum (http://www.the370z.com/)
-   The Lounge (Off Topic) (http://www.the370z.com/lounge-off-topic/)
-   -   The New “What did you do with your Z today” (with off topic replies) XXXVI (http://www.the370z.com/lounge-off-topic/133542-new-what-did-you-do-your-z-today-off-topic-replies-xxxvi.html)

BettyZ 04-30-2020 11:35 PM

Quote:

Originally Posted by vtec to vvel (Post 3930824)
Why ban me?? From one current lawyer to another future lawyer, we gots to stick together!

From a current lawyer to a future lawyer, we need to stab each other in the back as frequently and violently as we can. For the good of the species.

But seriously, that deodorant just looks so BOPPY!

BettyZ 04-30-2020 11:38 PM

Quote:

Originally Posted by redondoaveb (Post 3930826)
They are balls in an open race that get's lubricated by the sc oil

You had me at "balls."

Rusty 04-30-2020 11:47 PM

Quote:

Originally Posted by redondoaveb (Post 3930826)
They are balls in an open race that get's lubricated by the sc oil

Got it. Ceramic balls. Smoother and rounder then steel. A piece of grit will fvck them up. On the PAP units. Depending on rpm. Used either babbit plain bearings for high rpm, or steel ball bearings for low rpms. High rpms was over 50,000. A lot of it was over 100,000 rpms. all of it was pressure fed oil. The seals were ceramic. Could use your bare fingers touch them. The acid in you skin oil would damage the seals. Had to wear white cloth gloves and wipe the seals down with lens wipes.

redondoaveb 04-30-2020 11:54 PM

Quote:

Originally Posted by Rusty (Post 3930830)
Got it. Ceramic balls. Smoother and rounder then steel. A piece of grit will fvck them up. On the PAP units. Depending on rpm. Used either babbit plain bearings for high rpm, or steel ball bearings for low rpms. High rpms was over 50,000. A lot of it was over 100,000 rpms. all of it was pressure fed oil. The seals were ceramic. Could use your bare fingers touch them. The acid in you skin oil would damage the seals. Had to wear white cloth gloves and wipe the seals down with lens wipes.

My blower was spinning close to 62000. The bearings are suppose to be rated to 72000. Not quite as sensitive as what you were working with though. :rofl2:

BettyZ 05-01-2020 12:02 AM

Quote:

Originally Posted by redondoaveb (Post 3930831)
My blower was spinning close to 62000. The bearings are suppose to be rated to 72000. Not quite as sensitive as what you were working with though. :rofl2:

Rusty' sex toys have demanding tolerances. Nothing but the best!

Which only makes sense. Look [with eyepro] at what happened to jarboo and his chitty drilldo....

Rusty 05-01-2020 12:15 AM

Quote:

Originally Posted by BettyZ (Post 3930833)
Rusty' sex toys have demanding tolerances. Nothing but the best!

Which only makes sense. Look [with eyepro] at what happened to jarboo and his chitty drilldo....

When I worked at Elliott. Some of the equipment had tolerances of .0002". most was around .002". Ever use a pencil eraser to remove a high spot on a bearing journal? Scraping babbit bearings in? Bearing housing alignments?

redondoaveb 05-01-2020 12:28 AM

Quote:

Originally Posted by Rusty (Post 3930834)
When I worked at Elliott. Some of the equipment had tolerances of .0002". most was around .002". Ever use a pencil eraser to remove a high spot on a bearing journal? Scraping babbit bearings in? Bearing housing alignments?

Betty's too busy playing with her own balls.

Rusty 05-01-2020 12:48 AM

Quote:

Originally Posted by redondoaveb (Post 3930835)
Betty's too busy playing with her own balls.

Ben Wa Balls.

jchammond 05-01-2020 01:05 AM

:ugh:

jchammond 05-01-2020 03:12 AM

:ugh::ugh:

Zoren 370 05-01-2020 03:22 AM

Quote:

Originally Posted by BettyZ (Post 3930821)
It's vitally important in this time of Covid that we support the differently-abled. EW needs all the support he can get bro!

The dude is mighty strong sister!

Zoren 370 05-01-2020 03:26 AM

Good morning JC

jchammond 05-01-2020 03:29 AM

Quote:

Originally Posted by Zoren 370 (Post 3930847)
Good morning JC

Good morning Zoren :hello:

Spoiler 05-01-2020 03:30 AM

T-90

Spoiler 05-01-2020 03:30 AM

Good morning Boys....


All times are GMT -5. The time now is 05:21 PM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2