Nissan 370Z Forum
Page 86 of 669 « First 36768485 86 878896136186586 Last »
Show 40 post(s) from this thread on one page

Nissan 370Z Forum (http://www.the370z.com/)
-   The Lounge (Off Topic) (http://www.the370z.com/lounge-off-topic/)
-   -   The New "What did you do with your Z today" (with off topic replies) XXX (http://www.the370z.com/lounge-off-topic/128329-new-what-did-you-do-your-z-today-off-topic-replies-xxx.html)

onzedge 09-19-2018 09:11 PM
Quote:
Originally Posted by madwi (Post 3787005)
I love McIntosh amps.
My neighbors now "love" McIntosh amps as well...

:icon17:

Rusty 09-19-2018 09:15 PM
Quote:
Originally Posted by jchammond (Post 3787000)
THANK YOU JOBY!!!

ONE MILLION REPZ!!!!!!

WHO"S NEXT?

:eek: :tup: :happydance: :tiphat: :rofl2: :roflpuke2: :driving:

jwick 09-19-2018 09:15 PM
Quote:
Originally Posted by onzedge (Post 3787011)
My neighbors now "love" McIntosh amps as well...



:icon17:

I went to a the dark side and just run a sound bar and sub. So much easier.

I still have my full system setup in the TV room but I won’t be replacing any of it if it ***** the bed.

jchammond 09-19-2018 09:17 PM
No new tools today; ordered long hose pick set https://uploads.tapatalk-cdn.com/201...5e8f136c20.png
This is Bushing driver set,couple cushion grip hammers & a 14mm spark plug socket.
https://uploads.tapatalk-cdn.com/201...cd03858f19.pnghttps://uploads.tapatalk-cdn.com/201...648e6c842f.jpg
Socket was a bit late.


Sent from my iPad using Tapatalk

onzedge 09-19-2018 09:19 PM
Quote:
Originally Posted by Rusty (Post 3787014)
THANK YOU JOBY!!!

ONE MILLION REPZ!!!!!!

WHO"S NEXT?

:eek: :tup: :happydance: :tiphat: :rofl2: :roflpuke2: :driving:
Good job.

"Rep Freely" is a motto by which to live...

Rusty 09-19-2018 09:27 PM
Quote:
Originally Posted by JLarson (Post 3786981)
That is my entire job. One of our fabricators came in yesterday with questions about part marking location on a newly finished assembly. Turns out the reason she couldn't figure out the drawing view was that the welder welded a flange on backwards... Reject!
You should do QC on piping at a power plant during construction. :eek: I found control valves and check valves installed and welded in backwards. And this was after the welds was heat treated. :eek: :mad: I wasn't QC there. I was just walking down the different systems and learning where everything was at and the flow paths. It was part of my training to operate the plant.

madwi 09-19-2018 09:27 PM
Quote:
Originally Posted by jwick (Post 3787015)
I went to a the dark side and just run a sound bar and sub. So much easier.

I still have my full system setup in the TV room but I won’t be replacing any of it if it ***** the bed.
How do you like the soundbar? I gave away my old AV receiver a year ago and havent felt the need to replace it. I was looking for a simple setup that saved some space vs. 4ft tower speakers in the room.

madwi 09-19-2018 09:29 PM
Time for a Dew and some chicken tacos. :yum:

Spooler 09-19-2018 09:31 PM
Quote:
Originally Posted by jchammond (Post 3787016)
No new tools today; ordered long hose pick set https://uploads.tapatalk-cdn.com/201...5e8f136c20.png


Sent from my iPad using Tapatalk
Nice booger picker set.

Rusty 09-19-2018 09:46 PM
Quote:
Originally Posted by madwi (Post 3786982)
Well, I wouldnt mind a set of the deep sockets, the S bend wrenches and the half moon wrenches and while I am at it, a set of 0 offset wrenches. :rolleyes:
Think I'm done buying hand tools. Got everything I need almost. If I need something while doing a project. I'll get it.

I want a bigger air compressor. Have a 60 gallon now. But I could use a 120 gallon with a higher pressure shut off. Also want a Lincoln Precision TIG 225 Welder with the water cooler for the tig torch. A plasma cutter would be nice too. :yum: Press brake for bending sheet metal. A shear for cutting sheet metal. Tubing bender. A lift. AND a bigger garage for putting all of this in. :rofl2:

All ready have a Lincoln Pro Mig 180, and a Lincoln AC/DC stick welder.

Rusty 09-19-2018 09:51 PM
Quote:
Originally Posted by onzedge (Post 3786995)
Figures. It was done in China. :rofl2:

Rusty 09-19-2018 09:53 PM
Quote:
Originally Posted by jchammond (Post 3787007)
Thought those were apples...:confused:
I like the Fuji's. :yum:

madwi 09-19-2018 09:55 PM
Quote:
Originally Posted by Rusty (Post 3787029)
Think I'm done buying hand tools. Got everything I need almost. If I need something while doing a project. I'll get it.

I want a bigger air compressor. Have a 60 gallon now. But I could use a 120 gallon with a higher pressure shut off. Also want a Lincoln Precision TIG 225 Welder with the water cooler for the tig torch. A plasma cutter would be nice too. :yum: Press brake for bending sheet metal. A shear for cutting sheet metal. Tubing bender. A lift. AND a bigger garage for putting all of this in. :rofl2:

All ready have a Lincoln Pro Mig 180, and a Lincoln AC/DC stick welder.
It never ends my friend!

Rusty 09-19-2018 09:57 PM
Quote:
Originally Posted by Spooler (Post 3787024)
Nice booger picker set.
Those are for the hard to reach ones. :rofl2:

Rusty 09-19-2018 10:04 PM
Quote:
Originally Posted by madwi (Post 3787033)
It never ends my friend!
Tell me about it. :shakes head:

Forgot to add a 14x48 lathe, and a Bridgeport mill with 3 axis power. :yum:


All times are GMT -5. The time now is 08:02 PM.
Page 86 of 669 « First 36768485 86 878896136186586 Last »
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2