Nissan 370Z Forum - The New "What did you do with your Z today" (with off topic replies) XXX

Page 112 of 669

« First

112

Show 40 post(s) from this thread on one page

Nissan 370Z Forum (http://www.the370z.com/)

- The Lounge (Off Topic) (http://www.the370z.com/lounge-off-topic/)

- - The New "What did you do with your Z today" (with off topic replies) XXX (http://www.the370z.com/lounge-off-topic/128329-new-what-did-you-do-your-z-today-off-topic-replies-xxx.html)

BoneZ

09-23-2018 08:35 PM

My Camaro friends were being buttholes.

BoneZ

09-23-2018 08:36 PM

Not nice...
https://uploads.tapatalk-cdn.com/201...f5a6fc564f.jpg

eastwest2300

09-23-2018 09:52 PM

Quote:

Originally Posted by BoneZ (Post 3787809)

Crazy doooood

:eek::eek::eek::eek:

eastwest2300

09-23-2018 09:53 PM

Quote:

Originally Posted by BoneZ (Post 3787801)

Me too. You are on my list.

:ugh2::ugh2::ugh2::ugh2:

eastwest2300

09-23-2018 09:53 PM

Quote:

Originally Posted by BoneZ (Post 3787813)

My Camaro friends were being buttholes.

:ugh2::ugh2::ugh2::ugh2:

onzedge

09-23-2018 10:20 PM

Quote:

Originally Posted by eastwest2300 (Post 3787820)

:ugh2::ugh2::ugh2::ugh2:

Quote:

Originally Posted by eastwest2300 (Post 3787821)

:ugh2::ugh2::ugh2::ugh2:

Rep and be repped.

:tiphat:

BoneZ

09-24-2018 01:59 AM

Quote:

Originally Posted by onzedge (Post 3787823)

Rep and be repped.

:tiphat:

You are on my list too.

jchammond

09-24-2018 05:12 AM

:hello:
Good morning everyone!

jchammond

09-24-2018 05:35 AM

Quote:

Originally Posted by madwi (Post 3787797)

The kit will fit, but it is so close to everything. I was trying to reinvent the wheel really. Just seeing if I could get some additional clearance around the cmak fork end.

Jwick’s car probably didn’t come with “Frank” in the kit.
:ugh2:

jchammond

09-24-2018 05:41 AM

Quote:

Originally Posted by madwi (Post 3787797)

The kit will fit, but it is so close to everything. I was trying to reinvent the wheel really. Just seeing if I could get some additional clearance around the cmak fork end.

Dang I’d love to come back for another week; as we’d relocate the air-filter as well.
Agreed about clearance;especially with lowered car & thick rubber!
But I know how meticulous you are about every detail & that’s the way I’m wired. Attention to detail makes Night/Day difference in the long run!
:tup:

jchammond

09-24-2018 05:55 AM

Quote:

Originally Posted by Rusty (Post 3787641)

The 1st one. I drilled and used a burr bit to get the center section out. The next I used a hole saw. Which wasn't long enough to go all the way through. Still had to use a burr bit to get it out. This last one. I got a longer 2" hole saw. And cut all the way through. :tup:

I’ve done 2 so far & didn’t cut either one,,,just pulled them out with “Large Hardware” ... I’d like to say the 2nd one was easier- but my DA left an important piece at home while packing. I don’t rule out making a cut in the future/ as either Nissan puts some kinda glue on outer shell or they slide the bushing in while paint is wet on cross member.
I’m gonna put together a setup that won’t fail,,,even though the cross member isn’t truly flat/ I’ll compensate for that.
Someone mentioned about “freezing” the new solid bushing before installation & probably would have helped for sure.:tup:

eastwest2300

09-24-2018 06:16 AM

Quote:

Originally Posted by onzedge (Post 3787823)

Rep and be repped.

:tiphat:

I've officially entered Mr. Madwi's airspace..."rep at your own risk":eek::eek:

BoneZ

09-24-2018 06:26 AM

Quote:

Originally Posted by jchammond (Post 3787832)

:hello:
Good morning everyone!

Mernin'