NAH! Especially since installing those headers is such an easy, quick job!

Why do the pipes extend that long between the collectors and the flange ?! from what i remember the collectors exist just before the flanges, are these new design or somethin ?! Now they look like OBX headers lol !!

Did i miss the dyno sheet in this thread or somethin ?!

I don't know, those were the first pair I've installed on a local customer's car / first pair I've ever seen. Didn't know that they looked any different and I wasn't told they were redesigned. The fitment was excellent, the sound was amazing and the dyno results were posted in the VR Tune thread. The VR Tune and the headers were tested together. The customer's car came in with threads showing on his tires so we lost a lot of time ordering tires, mounting and balancing and getting it aligned. By the time we got all that done he was standing there waiting for us to flash the ECU. We got a couple of pulls on it and he had to take the car. So we got the baseline with the intake and catback and then the final dyno with the headers and flash.

Bump! Can you deny that sound?

Mine are at the coaters as we speak, putting them on this weekend.
http://www.rhoadescamaro.com/build/w...0-1024x579.jpg
Will try to get it on the dyno Monday. Test will be:
CAI + tune + stock manifolds + HFC + cat-back
vs.
CAI + tune + LTH + 3" 100cpi (mega high flow) cats + cat-back

I guess this is how they are building them now Glover997.

Installed, dyno tomorrow:
PPE Long-Tube Header install « J-Rho's '67 Camaro Z28 STX build

Nice write up j-rho. I especially liked the pic of you smiling before the pain :rofl2: If I've said it once, I've said it a thousand times...PPE headers are a major PITA to install especially the driver side.

Kudos for you installing them without removing the engine as did I. BTW, I had to make a wrench to reach/tighten the lower back nut on the driver side header.

Also, my butt dyno could tell the increase in HP after the install. Lastly, on the steering wheel linkage, there's an alignment flat spot on the spline shaft and yoke. That's what I used so I didn't have to go in and re-align.

Writeup here: Exhaust work and dyno session « J-Rho's '67 Camaro Z28 STX build

http://www.rhoadescamaro.com/build/w...S-1024x768.jpg

Great write up! Thanks for posting. It took us a solid 12 hours to install these on the black cherry convertible and it spent most of it's life by the ocean so we had a few f^*@in S*!+ moments.

The dip is a characteristic of the header -- the gains everywhere else more than make up for it tho'. You can minimize it somewhat with VVEL tuning (dial out some overlap in that rev range). Adding in a "choke", such as a single HFC, will flatten it out too -- but you might end up losing a few up top.

See further here http://www.the370z.com/south-east-re...-thread-7.html

We appreciate it when experts come in to talk about these products and share their knowledge. :)

That's because OBX copied PPE's design

OBX is said to be a much poorer quality. For the amount of labor it takes to install these, I'd spend the money to only have to do it once.

Bump - Good looks, solid gains, time consuming install but that SOUND!

Bump - Unleash some pent up power! Let your Z breathe! Lot's of deals this month! PM me for pricing.

All PM's responded to. Thank you for your continued interest, I look forward to assisting all of you further.

-Chris

Deals on Deals for the370z fam...New week is upon us, Lets Rock !

T.G.I.F. Get your orders in before the weekend

Fresh week fresh deals @ Vivid Racing...

Bump-Monday Deals...

For that sound!

Pulling the engine? Slap these on while you have the access!

Well worth the labor to install them!

All PM's replied to. All orders processed. Thank you once again for your business!

It's a brand new month, let's start it off right! Deals all over the place. Bring me pricing on anything I've quoted in the past and I will try to beat it. PM me, let me know what I can do to earn your business!

Todd

All PMs replied to, all orders processed! Thank you for your orders and for the continued business!! It is much appreciated!

For that F1 sound, great tone, great pitch and solid power gains!

How much shipped to 32025?
This would go with my ArK exhaust grip 2?
This negates the HfC right?

PM Sent! Thank you for your inquiry.

Anyone in AZ going to the No Fly Zone event out in Gila Bend on Oct 3rd?

Omega Motorsport Events

Stop by the tent and say hello! We will only be there Saturday.

All PMs answered, all orders processed! Thanks for the great week guys.

To any AZ locals, we will be out at the NO FLY ZONE ARIZONA at the Gila Bend Airstrip tomorrow with a couple Porsche 991 Turbos, the McLaren and our Vivid Racing Short Bus on Airbags! Come out for some 1/2 mile racing and good time! Gates open at 8 and the even will end around 3pm. The event will go through Sunday but Saturday seems to be the bigger attendance day. I'll be at home watching football on Sunday. Hope to see you there!

Thanks for all the inquiries on these guys!

Thanks for the orders guys! Would love to get the long tube sexiness on more 370s!

Who wants some long-tube goodies?

All PMs answered, all orders processed. Thank you for your business Z community!