Nissan 370Z Forum
Page 2 of 2 1 2
Show 40 post(s) from this thread on one page

Nissan 370Z Forum (http://www.the370z.com/)
-   Engine & Drivetrain (http://www.the370z.com/engine-drivetrain/)
-   -   IMPUL Hi Power Control Unit and big throttle valves (http://www.the370z.com/engine-drivetrain/14400-impul-hi-power-control-unit-big-throttle-valves.html)

Valentino 02-11-2010 08:40 AM
Acceleration, Throttle response, and some HP and TQ.

vipor 02-11-2010 08:42 AM
Returns on paper, not just conceptual ideals

Valentino 02-11-2010 08:45 AM
Quote:
Originally Posted by Valentino (Post 395345)
THROTTLE VALVE TRADE-IN = 116,000 JPY. about 1300 USD

NO TRADE-IN = 222,000 JPY. about 2500 USD
™ IMPUL Official Web site

I got my numbers from there Official website.

G37sHKS 02-13-2010 01:52 PM
Nice find guys.. I have a question though..

If we intall these throttle vavle.. do we have to custom a intake tube (bigger one) since these throttle valve body are larger than stock??

I mean can these throttle vavle body fit a stock intakes,stillen,injen..ETC?? or we have to do a custom tube??

Trips 02-13-2010 02:01 PM
Quote:
Originally Posted by theDreamer (Post 395370)
Just pancakes? I was hoping for a happy ending with those pancakes. :ugh2:
:iagree: :yum:

Valentino 02-13-2010 05:57 PM
Quote:
Originally Posted by G37sHKS (Post 400390)
Nice find guys.. I have a question though..

If we intall these throttle vavle.. do we have to custom a intake tube (bigger one) since these throttle valve body are larger than stock??

I mean can these throttle vavle body fit a stock intakes,stillen,injen..ETC?? or we have to do a custom tube??
These are stock throttle body.The outside diameter are the same. They just shaved some meat from the inside of the stock throttle. So no you won't need any custom intake tube.

to have an idea of what they did with the stock throttle watch this video from MINE'S go to minute 3:06

http://www.youtube.com/watch?v=<object width="560" height="340"><param name="movie" value="http://www.youtube.com/v/FdKpoop-3hk&hl=en_US&fs=1&"></param><param name="allowFullScreen" value="true"></param><param name="allowscriptaccess" value="always"></param><embed src="http://www.youtube.com/v/FdKpoop-3hk&hl=en_US&fs=1&" type="application/x-shockwave-flash" allowscriptaccess="always" allowfullscreen="true" width="560" height="340"></embed></object>

1slow370 02-14-2010 03:17 AM
Yup so basically "all we did was turn the bore larger on a lathe, mill the shaft down, and make a new buterfly. It cost us about $50 to do but please send us your $3000 dollars as we both know you have the cash to burn"


All times are GMT -5. The time now is 07:39 PM.
Page 2 of 2 1 2
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2