Rust on the lower engine part

SouthArk370Z · 07-06-2021, 08:46 PM

Quote:

Originally Posted by brainrain

So that I understand ( sorry I don’t understand English very well ) :

-I must not touch pulleys ( should I just clean up ? )

Not exactly true - you shouldn't get paint or other coating in the area where the belt rides, but it is OK to derust the entire pulley. The belt area probably doesn't need any derusting (the belt running over that area usually abrades any rust that might form); a few licks with a wire brush ought to do the job.

Quote:

Originally Posted by brainrain

- clean with vinegar the oil pan

Most weak acid solutions (citric, acetic, phosphoric, etc) will do the job. Some work better than others. The commercial products will usually have buffers and other agents to protect the metal.

Quote:

Originally Posted by brainrain

- use rust converter on just the oil pan like POR 15 ( but We haven’t this product, we have the product : wurth rust converter ) and paint after

I'd use the same chemical on everything. Just so I didn't have to handle more than one solution. Shouldn't matter all that much which one you use. YMMV

Quote:

Originally Posted by brainrain

What is the temperature of the oil pan please ? (When engine is hot ) Because temp max for Wurth rust converter is 120 degrees ( 248 F)

I think that is the max temp to use the rust converter. The temp after treatment shouldn't matter. But I'm not sure.

Edit: According to https://eshop.wuerth.com.mt/images/u...ets/893110.pdf , "Thermally stable up to +120°C for short periods." I take that to mean you can use it for a very short time at that temp and does not apply after treatment. You might want to verify that with another source.

Quote:

Originally Posted by brainrain

Should I use high temp paint?

Shouldn't be necessary unless you have parts near the exhaust manifold. But it doesn't do any harm.

Tractionless · 07-07-2021, 01:04 PM

Use Fozz for corrosion inhibitor.

gbrettin · 07-14-2021, 09:59 AM

Functionally everything should work correctly with out doing anything.

If you want to remove the rust for cosmetics... Well, that's going to be tricky like the others have already stated.

Here's the path I would take. New belt, upgrade sway bar w/ SPL end links, ATI Damper and remove/cleanup the idler pulleys (or get new ones depending on the miles).

Here's the rub though... I suspect you have other rust concerns in there lurking that you just haven't seen.

07-07-2021, 01:04 PM	#17 (permalink)
Tractionless A True Z Fanatic Join Date: Jan 2016 Location: Atlantic SE Posts: 1,237 Drives: '10 K23 ST 7AT Rep Power: 30525	Use Fozz for corrosion inhibitor. __________________ Toys Not Tots

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Rust in 2017 Engine Bay?	370zHawaii	Nissan 370Z General Discussions	6	02-13-2019 11:39 AM
lower engine splash guard	fairlady_z34	Exterior & Interior	5	12-12-2013 05:59 PM
[WTB] Lower engine cover shroud	RedNismoZ	Parts for sale (Private Classifieds)	18	10-25-2012 02:55 AM
Lower engine cover	bigrob126	Nissan 370Z General Discussions	6	04-29-2011 12:14 PM
underbody/engine block rust prevention?	ADmaster71690	Exterior & Interior	13	08-31-2009 05:34 PM

07-14-2021, 09:59 AM	#18 (permalink)
gbrettin A True Z Fanatic Join Date: Oct 2010 Location: Portage, MI Posts: 2,237 Drives: Tricycle Rep Power: 542172	Functionally everything should work correctly with out doing anything. If you want to remove the rust for cosmetics... Well, that's going to be tricky like the others have already stated. Here's the path I would take. New belt, upgrade sway bar w/ SPL end links, ATI Damper and remove/cleanup the idler pulleys (or get new ones depending on the miles). Here's the rub though... I suspect you have other rust concerns in there lurking that you just haven't seen.