DIY: Homelink install in a Base/Nismo

Nubz · 06-03-2010, 06:30 PM

Im looking for the Gentex 453-series and I did a search on ebay and did not find one. If i go through Nissan will it be the Gentex 453-series?

errett · 07-08-2010, 06:53 PM

Many thanks...just got done doing the install.

E

tjlazer · 07-08-2010, 06:58 PM

Quote:

Originally Posted by Nubz

Im looking for the Gentex 453-series and I did a search on ebay and did not find one. If i go through Nissan will it be the Gentex 453-series?

Do a search for Nissan Maxima Homelink mirrors, 2006 and up. Thats what mine came from and its the Gentex 453 with Amber Compass LED!

DIGItonium · 07-11-2010, 12:41 AM

I completed the installation today and managed to move the BT microphone from the A pillar to the map light area. The diagrams indicated a couple of spots for microphones for vehicles with BT, so I glued the microphone to that location. It hasn't been tested yet.

Anyhow, everything seems to be working. Well, the compass still shows C and I've had time to mess with it yet. Auto-dimming seems to work. However, Homelink isn't working at all. No lights when I press or hold any of the buttons. :-(

I checked the voltage at the T-taps, and it comes up good.

[EDIT] Resolved. Battery wire gauge to the t-tap was too small, so it didn't fully cut the insulation causing intermittent connection. It works now

SE · 07-22-2010, 03:22 PM

^ are you still getting the "C" on the compass area? you may need to drive around a bit in a clear area (with a clear view of the sky) to get it to calibrate.

flashburn · 07-22-2010, 03:48 PM

Got my Homelink mirror as a birthday present last week. Going to install it this weekend, woohoo. Thanks again for the DIY, looks pretty straight forward.

flashburn · 07-24-2010, 10:23 AM

Quote:

Originally Posted by weeeee

There should be a small black plastic tab on the bottom of the mirror attached to the window. Gently push up on this tap and pull up on the actual mirror mount. The mirror will come straight off. The tab is here-

Maybe I'm retarded, but I can't for the life of me figure this part out. I've tried pushing that little black tab up towards the windshield and it doesn't move at all. I've been pushing certainly a lot harder than "gently" that is for sure. Any help? Sweating my *** off here.

flashburn · 07-24-2010, 10:55 AM

Went and gave it another shot and was able to get it off. Pretty sure your directions are wrong though, the tab should be pulled down slightly... or at least thats what it seemed like I did when it finally came off.

DIGItonium · 07-24-2010, 12:23 PM

Quote:

Originally Posted by weeeee

^ are you still getting the "C" on the compass area? you may need to drive around a bit in a clear area (with a clear view of the sky) to get it to calibrate.

Yea, I drove in circles a few times and it started working.

SE · 07-24-2010, 03:29 PM

Quote:

Originally Posted by flashburn

Went and gave it another shot and was able to off. Pretty sure your directions are wrong though, the tab should be pulledbec down slightly... or at least thats what it seemed like I did when it finally came off.

Sorry for the confusion. I meant pull up on the tab meaning towards you, like a soda can. At the same time you're pulling on the tab, you should be pushing up on the mirror. I said gently because you don't want to crack windshield glass when trying to get it off.

DIGItonium · 07-24-2010, 04:18 PM

That OEM mirror was a bit of a pain to remove. I spent 30min trying to figure out the tab, so I pried and snapped it. The mirror was out afterwards with no visible damage to the glass. However, the wire cover that came with it is a bit on the short side.

BTW, for those who run a microphone to the a-pillar, it's nice to route and hide the mic underneath the map light switch location. Look Ma! No Wires!

flashburn · 07-24-2010, 05:12 PM

Heh, the wire cover that came with mine was too long, couldn't use it. I'll probably pick up or order the Nissan one next time I'm at the dealer.

G Fo12ce · 08-19-2010, 06:25 PM

Quote:

Originally Posted by DIGItonium

That OEM mirror was a bit of a pain to remove. I spent 30min trying to figure out the tab, so I pried and snapped it. The mirror was out afterwards with no visible damage to the glass. However, the wire cover that came with it is a bit on the short side.

BTW, for those who run a microphone to the a-pillar, it's nice to route and hide the mic underneath the map light switch location. Look Ma! No Wires!

Digitonium do you have any pics of the new mic location? I just got a new head unit with BT and I'm thinking of doing the mirror at the same time.

DIGItonium · 08-19-2010, 11:10 PM

Quote:

Originally Posted by G Fo12ce

Digitonium do you have any pics of the new mic location? I just got a new head unit with BT and I'm thinking of doing the mirror at the same time.

Sorry, no pictures of the microphone installed. However, you can follow the instructions to change the ambient LED:
DIY: Interior LED Color Change

From there you should be able route the microphone wire through the headliner as you would when hiding the wires for the rearview mirror. Then you can push the microphone through the headliner and out through the map light area.

I tore the dust cloth and secured the microphone with epoxy. Make sure the microphone is aimed towards the opening. You can use masking tape to hold it in place before applying epoxy. Let it set for a few hours before removing the masking tape.

The headunit should have adjustments for the microphone. I think I had it close to max. My gf complains about hearing me sometimes, but so far everyone's able to hear me fine.

oreocrumble · 09-06-2010, 08:42 AM

I just did this install but I cant figure out how to program homelink. When I try resetting memory by pressing two outer buttons , nothing happens. My compass works fine and my auto dimming too. Any ideas or suggestions ?

07-11-2010, 12:41 AM	#19 (permalink)
DIGItonium A True Z Fanatic Join Date: Jan 2009 Location: Kansas Posts: 3,800 Drives: 09 Z34-TT 6MT Rep Power: 43	I completed the installation today and managed to move the BT microphone from the A pillar to the map light area. The diagrams indicated a couple of spots for microphones for vehicles with BT, so I glued the microphone to that location. It hasn't been tested yet. Anyhow, everything seems to be working. Well, the compass still shows C and I've had time to mess with it yet. Auto-dimming seems to work. However, Homelink isn't working at all. No lights when I press or hold any of the buttons. :-( I checked the voltage at the T-taps, and it comes up good. [EDIT] Resolved. Battery wire gauge to the t-tap was too small, so it didn't fully cut the insulation causing intermittent connection. It works now __________________ Last edited by DIGItonium; 07-11-2010 at 02:05 PM.

07-24-2010, 04:18 PM	#26 (permalink)
DIGItonium A True Z Fanatic Join Date: Jan 2009 Location: Kansas Posts: 3,800 Drives: 09 Z34-TT 6MT Rep Power: 43	That OEM mirror was a bit of a pain to remove. I spent 30min trying to figure out the tab, so I pried and snapped it. The mirror was out afterwards with no visible damage to the glass. However, the wire cover that came with it is a bit on the short side. BTW, for those who run a microphone to the a-pillar, it's nice to route and hide the mic underneath the map light switch location. Look Ma! No Wires! __________________

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Double DIN install in Base System opening	355890	Audio & Video	5	06-29-2015 10:33 PM
Request: Homelink mirror install	Skorch	DIY Section (Do-It-Yourself)	25	05-08-2010 10:59 PM
Nismo struts install	cab83_750	Brakes & Suspension	25	02-14-2010 04:40 PM
Base (w/Nismo Parts - Non Nismo Z) vs Sport Package	kraphy	Engine & Drivetrain	10	09-24-2009 12:15 PM
Rear speaker install on a base 370z	Carbon_z	Audio & Video	15	09-17-2009 02:58 PM

06-03-2010, 06:30 PM	#16 (permalink)
Nubz Base Member Join Date: Mar 2010 Location: Orlando, Fla Posts: 142 Drives: 2010 PG 370Z A7 Rep Power: 16	Im looking for the Gentex 453-series and I did a search on ebay and did not find one. If i go through Nissan will it be the Gentex 453-series?

07-08-2010, 06:53 PM	#17 (permalink)
errett Base Member Join Date: Mar 2010 Location: Maumelle, AR Posts: 149 Drives: Z34 10 0111 Rep Power: 16	Many thanks...just got done doing the install. E

07-22-2010, 03:22 PM	#20 (permalink)
SE A True Z Fanatic Join Date: Jan 2010 Location: San Jose, CA Posts: 4,236 Drives: 370z/STI/EVO X/IS-F Rep Power: 24	^ are you still getting the "C" on the compass area? you may need to drive around a bit in a clear area (with a clear view of the sky) to get it to calibrate.

07-22-2010, 03:48 PM	#21 (permalink)
flashburn A True Z Fanatic Join Date: May 2009 Location: Central Florida Posts: 1,884 Drives: '12 Corvette GS 6M Rep Power: 20	Got my Homelink mirror as a birthday present last week. Going to install it this weekend, woohoo. Thanks again for the DIY, looks pretty straight forward.

07-24-2010, 10:55 AM	#23 (permalink)
flashburn A True Z Fanatic Join Date: May 2009 Location: Central Florida Posts: 1,884 Drives: '12 Corvette GS 6M Rep Power: 20	Went and gave it another shot and was able to get it off. Pretty sure your directions are wrong though, the tab should be pulled down slightly... or at least thats what it seemed like I did when it finally came off.

07-24-2010, 05:12 PM	#27 (permalink)
flashburn A True Z Fanatic Join Date: May 2009 Location: Central Florida Posts: 1,884 Drives: '12 Corvette GS 6M Rep Power: 20	Heh, the wire cover that came with mine was too long, couldn't use it. I'll probably pick up or order the Nissan one next time I'm at the dealer.

09-06-2010, 08:42 AM	#30 (permalink)
oreocrumble Base Member Join Date: Apr 2010 Location: Puerto Rico Posts: 21 Drives: 10 Nissan 370z M6 Rep Power: 16	I just did this install but I cant figure out how to program homelink. When I try resetting memory by pressing two outer buttons , nothing happens. My compass works fine and my auto dimming too. Any ideas or suggestions ?