DIY stuck brake lines, Help Please!

newtonova822 · 05-24-2014, 06:38 PM

On a new 2014 sport with 300 miles adding Z1 SS lines but back stock wont free from block. All others on back will break loose. The small line that feeds into new brass block on Z1 lines. at point on rounding fitting with open end 10mm..

Any suggestions???

Trips · 05-24-2014, 06:48 PM

Try using some WD-40 and reposition the wrench or use vise-grips as a last resort

EDIT: There is NO reason for making multiple threads for the same thing.

One is enough just be patient.

Mike · 05-24-2014, 07:32 PM

NEVER use an open end wrench on a brake line! Go spend the $10 on a proper flare nut wrench.

SouthArk370Z · 05-24-2014, 10:25 PM

Quote:

Originally Posted by Mike

NEVER use an open end wrench on a brake line! Go spend the $10 on a proper flare nut wrench.

I can't agree with this enough. Cheap at twice the price for the headaches it will save.

thompsontechs · 06-06-2014, 01:18 PM

I agree with both the above, once you start to round it you might not even be able to get a line wrench on it anymore.

I prefer PB Blaster to WD.

You can also try some heat, but be careful... if you resort to ViceGrips you have already destroyed it and the line should be replaced. DO NOT get one of those line splicing kits with the union... it WILL fail.

If it's shot already then use whatever means to get it out and replace the entire line.

JT

newtonova822 · 06-13-2014, 11:47 AM

This should do it.

05-24-2014, 06:38 PM	#1 (permalink)
newtonova822 Base Member Join Date: May 2014 Location: No Va Posts: 70 Drives: 2014-370Z-White_Manu Rep Power: 11	DIY stuck brake lines, Help Please! On a new 2014 sport with 300 miles adding Z1 SS lines but back stock wont free from block. All others on back will break loose. The small line that feeds into new brass block on Z1 lines. at point on rounding fitting with open end 10mm.. Any suggestions???

05-24-2014, 06:48 PM	#2 (permalink)
Trips Administrator Join Date: May 2009 Location: Disneyland, Ca Posts: 8,728 Drives: 🔰 Rep Power: 10	Try using some WD-40 and reposition the wrench or use vise-grips as a last resort EDIT: There is NO reason for making multiple threads for the same thing. One is enough just be patient. __________________ Last edited by Trips; 05-24-2014 at 06:51 PM.

05-24-2014, 07:32 PM	#3 (permalink)
Mike The370Z.com Sponsor Join Date: Jun 2009 Location: Loganville, GA Posts: 5,944 Drives: 370z Rep Power: 2185	NEVER use an open end wrench on a brake line! Go spend the $10 on a proper flare nut wrench. fuct, Trips, kenchan and 7 others like this. __________________ NISSAN: 75 280Z / 86 300ZX GLL /87 Sentra SE / 03 350Z / 23 Z Porsche: 93 968 / 23 Macan GTS / 93 968

06-13-2014, 11:47 AM	#6 (permalink)
newtonova822 Base Member Join Date: May 2014 Location: No Va Posts: 70 Drives: 2014-370Z-White_Manu Rep Power: 11	bought 11m flarenut wrench This should do it.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
throttle stuck and brake light on	Big J	Nissan 370Z Warranty / Scheduled Maintenance / Servicing / Repairs	1	10-06-2015 01:44 AM
stuck brake line fittings.. suggestions?	newtonova822	DIY Section (Do-It-Yourself)	4	05-29-2014 06:36 PM
SS Brake Lines	chrisbeltre	Brakes & Suspension	0	03-18-2012 06:51 PM
Place in dallas to install brake lines and clutch lines?	rambunctious	Texas	0	02-05-2011 02:13 PM

06-06-2014, 01:18 PM	#5 (permalink)
thompsontechs Base Member Join Date: Apr 2014 Location: Rockford Posts: 129 Drives: 370 Sport Rep Power: 11	I agree with both the above, once you start to round it you might not even be able to get a line wrench on it anymore. I prefer PB Blaster to WD. You can also try some heat, but be careful... if you resort to ViceGrips you have already destroyed it and the line should be replaced. DO NOT get one of those line splicing kits with the union... it WILL fail. If it's shot already then use whatever means to get it out and replace the entire line. JT