My_third_Z's SQ system

bigaudiofanat · 02-20-2012, 08:54 PM

Quote:

Originally Posted by My_third_Z

One set is going in the stock door location and I'm building a set of kickpanels to hold the other pair.

You wanting a lot of mid bass?

I would recommend running the KRX3's and put a 4 inch in the custom kick panel. Just some advice.

My_third_Z · 02-20-2012, 09:40 PM

Quote:

Originally Posted by bigaudiofanat

You wanting a lot of mid bass?

I would recommend running the KRX3's and put a 4 inch in the custom kick panel. Just some advice.

I've considered getting that set and putting the 4" in the door with the 6.5" in the kickpanel. I'll see how this sounds after it gets done. It wouldn't be difficult to swap out the door speakers if I decide it's too much midbass. I was planning on setting different crossover points for the 6.5s so they play a slightly different range, but honestly it will just involve some tinkering with the EQ once it's done.

My_third_Z · 02-20-2012, 09:43 PM

Quote:

Originally Posted by Omikron

Awesome, would love pics when you get to that point. Thanks.

Definitely. I'm in the middle of 13 straight days of work where I'll put in about 145 hours, so spare time has been limited. Hopefully I can make some good progress in the next couple weeks and get some pictures up. I'm planning a couple weeks of vacation in May, so that will probably be when most of the work takes place. I was just excited to finally get all my stuff in, and couldn't resist showing it off already.

37Z · 02-21-2012, 06:13 AM

Quote:

Originally Posted by My_third_Z

I was just out trying to fit the stuff in different configurations. I'm at a loss right now how it's all going to fit in there. I definitely don't want to lose the spare, but other than that, I'm fine taking all the free space. The sub is going to be mounted inside out. That will help cut down on the amount of air space required since the basket and magnet structure will be outside.
I'm still trying to figure out a way to have the amps and processor on the shelf behind the seats. They'll all fit there, but I was wanting to have the processor centered between the seats and the 4 channel amp makes that impossible.

Their is a ton of space for the amp, sub, audio controll, if you loose the spare and jack inlcuiding its foam pieces. If so, add a 12-volt tire pump, and a few cans of fix-a-flat and your will have almost the same emergency tire equipment. Plus the weight savings of no spare, jack is a plus.

Omikron · 02-21-2012, 08:37 AM

Quote:

Originally Posted by My_third_Z

Definitely. I'm in the middle of 13 straight days of work where I'll put in about 145 hours, so spare time has been limited. Hopefully I can make some good progress in the next couple weeks and get some pictures up. I'm planning a couple weeks of vacation in May, so that will probably be when most of the work takes place. I was just excited to finally get all my stuff in, and couldn't resist showing it off already.

I don't blame you at all, amazing gear for sure.

I am pretty interested in the kick panel build. I thought about that but was told there wasnt really enough room on the driver side. Anyway, looking forward to seeing how you do it. Also looking forward to see how you like that much mid-bass.

12 hour days for 13 days straight, ugh...

My_third_Z · 02-21-2012, 01:20 PM

Quote:

Originally Posted by 37Z

Their is a ton of space for the amp, sub, audio controll, if you loose the spare and jack inlcuiding its foam pieces. If so, add a 12-volt tire pump, and a few cans of fix-a-flat and your will have almost the same emergency tire equipment. Plus the weight savings of no spare, jack is a plus.

I was always under the impression that fix-a-flat damaged your rim somehow if you had to use it. Am I wrong in believing that?

My_third_Z · 02-21-2012, 01:29 PM

Quote:

Originally Posted by Omikron

I don't blame you at all, amazing gear for sure.

I am pretty interested in the kick panel build. I thought about that but was told there wasnt really enough room on the driver side. Anyway, looking forward to seeing how you do it. Also looking forward to see how you like that much mid-bass.

12 hour days for 13 days straight, ugh...

Those long days of overtime are what's helping pay for this little bit of craziness. I don't even want to look at my credit card statement this month. It'd be great if I could log-in blindly and just click "pay".

Omikron · 02-21-2012, 03:49 PM

Quote:

Originally Posted by My_third_Z

Those long days of overtime are what's helping pay for this little bit of craziness. I don't even want to look at my credit card statement this month. It'd be great if I could log-in blindly and just click "pay".

37Z · 02-22-2012, 11:45 AM

Quote:

Originally Posted by My_third_Z

I was always under the impression that fix-a-flat damaged your rim somehow if you had to use it. Am I wrong in believing that?

I heard that as well but, I have not heard anything conclusive. I do not know if SLIME has rim issues or not.

Cadillac's vehicles include a similar can of fix-a-flat that supposely does not have rim issues. I think you can order there emergency kit from any of those dealers.

My_third_Z · 03-02-2012, 11:03 PM

I will have some updates with pictures tomorrow evening. If all goes well, the kickpanels will be done by then. I'm still planning on sending them out to get wrapped in carbon fiber, so they won't be totally complete, but my part will be done.
On a side note, to anyone else considering kickpanels with a manual transmission, you may want to consider something else. The driver side one is being a pain, but I think I've got it figured out now. It's definitely going to be a tight fit. Hopefully it won't hamper pushing in the clutch.

My_third_Z · 03-05-2012, 03:06 AM

Only a day late on this update. Stupid weather yesterday was not conducive to working on a car. I was hoping to have the base for the amp rack built, but I don't have a garage and it was pouring rain.

Here is my progression with the kickpanels. Steps so far...
1. taping the area, laying down aluminum foil, and then taping over that
2. covering everything nearby in plastic (fiberglass in carpet = permanent)
3. putting down the resin and fiberglass mat
4. the molds after removal from car
5. speaker rings mounted
6. passenger side wrapped and first couple layers of body filler added. It's looking really good so far, but there's still a lot of sanding left.

You'll notice the driver's side panel has a hole cut in the back. I had to do that to get the speaker far enough away from the clutch. I'll go back later and full enclose it, but left the hole for now. Thankfully there's enough room to recess that speaker some. Weather permitting, next weekend I will have the amp rack started.

bigaudiofanat · 03-05-2012, 04:51 AM

Nice work, how man layers did you wrap the top before the layer of bondo? At least 3 I hope.

BigNate · 03-05-2012, 07:57 AM

looks good dude but that is a little much on the bondo it is there to fill un even areas you hardly need to cover an entire piece as it does not add much strength

My_third_Z · 03-05-2012, 02:44 PM

I did the layer of fleece and then two layers of mat on top of that. It's solid as a rock.
I know it's bit too much bondo, but some of my skills have diminished over the years. It's been at least 12 years since I did any fiberglass work and I'm having to relearn some tricks. That's why I started with the kickpanels, since they're the smallest parts I'm planning on fabricating. In the end they'll be strong and look good, although it may take a good bit more sanding than someone who is proficient at it.

Omikron · 03-06-2012, 08:25 AM

Quote:

Originally Posted by My_third_Z

Only a day late on this update. Stupid weather yesterday was not conducive to working on a car. I was hoping to have the base for the amp rack built, but I don't have a garage and it was pouring rain.

Here is my progression with the kickpanels. Steps so far...
1. taping the area, laying down aluminum foil, and then taping over that
2. covering everything nearby in plastic (fiberglass in carpet = permanent)
3. putting down the resin and fiberglass mat
4. the molds after removal from car
5. speaker rings mounted
6. passenger side wrapped and first couple layers of body filler added. It's looking really good so far, but there's still a lot of sanding left.

You'll notice the driver's side panel has a hole cut in the back. I had to do that to get the speaker far enough away from the clutch. I'll go back later and full enclose it, but left the hole for now. Thankfully there's enough room to recess that speaker some. Weather permitting, next weekend I will have the amp rack started.

Wow, nice work. I actually had no idea how any of this worked. Pretty cool to see the pics like this. Thanks! Keep updating if you can.

03-05-2012, 04:51 AM	#27 (permalink)
bigaudiofanat Car Audio Installer Join Date: Jun 2009 Location: Magnolia DE Posts: 8,342 Drives: 2012 Infiniti G37x Rep Power: 853	Nice work, how man layers did you wrap the top before the layer of bondo? At least 3 I hope. __________________ Need help with car audio or electronics? Let me know!! Need Help Let Me Know Direct email address reimermatt@gmail.com Owner of: Dynamic Mobile Audio Follow me below https://www.facebook.com/Dynamicmobileaudio/

03-05-2012, 07:57 AM	#28 (permalink)
BigNate Base Member Join Date: Jan 2012 Location: Charlotte, nc Posts: 87 Drives: 07 Element SC Rep Power: 14	looks good dude but that is a little much on the bondo it is there to fill un even areas you hardly need to cover an entire piece as it does not add much strength __________________ MECP Master Certified Installation Technician Don't worry I've never done this before

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
ARK PERFORMANCE USA dot COM : 370Z/Z34/VQ37 GRIP EXHAUST SYSTEM FULL CATBACK SYSTEM	TeamARK	Intake/Exhaust	25	09-01-2011 11:27 AM
OEM Base Audio System to Full Bose System Swap / Conversion?	TopGone	Audio & Video	5	02-15-2011 11:34 PM
Nav system	raul	New 370Z Owner	2	07-01-2010 03:17 PM
more torque vs. less/dry sump oil system vs. reg. oil system?	tvfreakazoid	Nissan 370Z General Discussions	7	03-09-2010 02:52 AM
Nav system	Monty	Audio & Video	2	04-29-2009 09:46 PM

03-02-2012, 11:03 PM	#25 (permalink)
My_third_Z Enthusiast Member Join Date: Feb 2011 Location: Charleston,SC Posts: 312 Drives: Blue 09 370z Rep Power: 15	I will have some updates with pictures tomorrow evening. If all goes well, the kickpanels will be done by then. I'm still planning on sending them out to get wrapped in carbon fiber, so they won't be totally complete, but my part will be done. On a side note, to anyone else considering kickpanels with a manual transmission, you may want to consider something else. The driver side one is being a pain, but I think I've got it figured out now. It's definitely going to be a tight fit. Hopefully it won't hamper pushing in the clutch.

03-05-2012, 02:44 PM	#29 (permalink)
My_third_Z Enthusiast Member Join Date: Feb 2011 Location: Charleston,SC Posts: 312 Drives: Blue 09 370z Rep Power: 15	I did the layer of fleece and then two layers of mat on top of that. It's solid as a rock. I know it's bit too much bondo, but some of my skills have diminished over the years. It's been at least 12 years since I did any fiberglass work and I'm having to relearn some tricks. That's why I started with the kickpanels, since they're the smallest parts I'm planning on fabricating. In the end they'll be strong and look good, although it may take a good bit more sanding than someone who is proficient at it.