Nissan 370Z Forum  

Go Back   Nissan 370Z Forum > Search Forums


Showing results 1 to 13 of 13
Search took 0.00 seconds.
Search: Posts Made By: Dwight Frye
Forum: DIY Section (Do-It-Yourself) 10-11-2012, 06:15 PM
Replies: 503
Views: 106,611
Posted By Dwight Frye
You should (A) tell the service manager at your...

You should (A) tell the service manager at your local dealer that "irregardless" isn't a real word, and (B) spend the money for the harness and install it yourself.
It's about the cost of a few fast...
Forum: DIY Section (Do-It-Yourself) 06-18-2012, 06:03 PM
Replies: 503
Views: 106,611
Posted By Dwight Frye
To the pros for the harness, it only requires a...

To the pros for the harness, it only requires a tiny screwdriver blade to press down the lock tab on the factory connector at lock, and a set of diagonal cutters or scissors to trim the extra plastic...
Forum: DIY Section (Do-It-Yourself) 06-04-2012, 05:51 PM
Replies: 503
Views: 106,611
Posted By Dwight Frye
What would be the procedure to reconnect the...

What would be the procedure to reconnect the brown wire ? Would it be:
Engine off, ignition in ACC position which would tell the ECU to "unlock"
Reconnect brown wire
Ignition button back to OFF...
Forum: DIY Section (Do-It-Yourself) 06-03-2012, 07:56 PM
Replies: 503
Views: 106,611
Posted By Dwight Frye
I received mine yesterday. Thanks for including...

I received mine yesterday. Thanks for including printed instructions, I put them in the pouch with the owner's manual in the hatch area. Installation was a piece'o'cake, took longer to readjust my...
Forum: DIY Section (Do-It-Yourself) 05-19-2012, 08:18 PM
Replies: 503
Views: 106,611
Posted By Dwight Frye
Good man ! I just completed a PayPal transaction...

Good man ! I just completed a PayPal transaction for the harness.
Thanks
Forum: DIY Section (Do-It-Yourself) 05-18-2012, 05:30 PM
Replies: 503
Views: 106,611
Posted By Dwight Frye
Question for BDL99: Are you going to do a...

Question for BDL99: Are you going to do a continuity check on each wire in each harness to be sure there are no cold solders or bad pin connections before sending the harnesses out ? I'd just like to...
Forum: DIY Section (Do-It-Yourself) 05-11-2012, 06:08 PM
Replies: 503
Views: 106,611
Posted By Dwight Frye
I just have to comment positively about this...

I just have to comment positively about this site. Back in the early 80's I was a member of an RX-7 club. Once a month I'd get a newsletter with photos and Q&A's and owners tips, etc. Then, the...
Forum: DIY Section (Do-It-Yourself) 05-10-2012, 06:40 PM
Replies: 503
Views: 106,611
Posted By Dwight Frye
From my admittedly limited knowledge of the...

From my admittedly limited knowledge of the circuits involved with the lock, I think all of the other wires except the brown one have to still be connected to the lock mechanism as there is some kind...
Forum: DIY Section (Do-It-Yourself) 05-08-2012, 06:30 PM
Replies: 503
Views: 106,611
Posted By Dwight Frye
Pictures or it didn't happen

Pictures or it didn't happen
Forum: DIY Section (Do-It-Yourself) 05-04-2012, 07:14 PM
Replies: 503
Views: 106,611
Posted By Dwight Frye
I'll take a straight harness without a switch. I...

I'll take a straight harness without a switch. I don't see the need for a switch while parking. If I want to reactivate the lock function for example, if I were to trade in or sell the car, I would...
Forum: DIY Section (Do-It-Yourself) 04-27-2012, 06:05 PM
Replies: 503
Views: 106,611
Posted By Dwight Frye
I'm in if it works too. Great work guys !

I'm in if it works too. Great work guys !
Forum: DIY Section (Do-It-Yourself) 04-25-2012, 06:10 PM
Replies: 503
Views: 106,611
Posted By Dwight Frye
A harness needs to be under $100.00 Closer to $50...

A harness needs to be under $100.00 Closer to $50 would be better. Otherwise when my warranty runs out I'll just cut the brown wire and live without the lock feature. If someone is going to steal the...
Forum: DIY Section (Do-It-Yourself) 04-20-2012, 05:16 PM
Replies: 503
Views: 106,611
Posted By Dwight Frye
So it is as simple as making sure the wheel is...

So it is as simple as making sure the wheel is unlocked first, and then cutting one wire and taping off the cut end with electrical tape so it doesn't short ? If this works I would be happy to forego...
Showing results 1 to 13 of 13

 
Forum Jump

All times are GMT -5. The time now is 05:40 PM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2