|
It is Monday April 22nd and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Lite Speed Titanium Exhaust Nissan 370Z: Introducing Litespeed Racing’s all new full titanium race exhaust for Nissan 370z. This is a no-holds-barred, ultra-high performance exhaust system designed for track and street use. Its unique straight pipe design makes it one of the lightest and most aggressive systems on the market. Oversized rear resonators eliminate drone and keep sound levels down at street speeds, all while producing +14 peak horse power and +16 pound feet of torque over the NISMO exhaust. At only 14.2 pounds, it is 38 pounds less than stock. AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains. Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU. AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Tuesday April 23rd and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Lite Speed Titanium Exhaust Nissan 370Z: Introducing Litespeed Racing’s all new full titanium race exhaust for Nissan 370z. This is a no-holds-barred, ultra-high performance exhaust system designed for track and street use. Its unique straight pipe design makes it one of the lightest and most aggressive systems on the market. Oversized rear resonators eliminate drone and keep sound levels down at street speeds, all while producing +14 peak horse power and +16 pound feet of torque over the NISMO exhaust. At only 14.2 pounds, it is 38 pounds less than stock. AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains. Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU. AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Wednesday April 24th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Lite Speed Titanium Exhaust Nissan 370Z: Introducing Litespeed Racing’s all new full titanium race exhaust for Nissan 370z. This is a no-holds-barred, ultra-high performance exhaust system designed for track and street use. Its unique straight pipe design makes it one of the lightest and most aggressive systems on the market. Oversized rear resonators eliminate drone and keep sound levels down at street speeds, all while producing +14 peak horse power and +16 pound feet of torque over the NISMO exhaust. At only 14.2 pounds, it is 38 pounds less than stock. AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains. Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU. AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Tuesday April 25th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Tanabe Medalian Exhaust - Medalion Touring: A refined level of performance and driveability is available in the MEDALION TOURING. The elegant, well defined appearance of MEDALION TOURING is mature, and matches the artistry of a tastefully built, highly tuned machine. Using the all new 'continuous strand' ADVANTEX packing material technology, MEDALION TOURING acheives extremely high levels of exhaust system efficiency, while maintaining a street driveable, extremely low frequency and deep tone that is well under 93db for discreet sports driving. This system requires no removeable silencer for under 93db operation at all rpms. The extremely deep, low frequency tone keeps in-cabin noise to a minimum. The full SUS304 stainless MEDALION TOURING features a slim-line oval canister, and a special dual wall, angle-cut tip. This premium quality system is for sports driving. AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains. Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU. AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Friday April 26th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Tanabe Medalian Exhaust - Medalion Touring: A refined level of performance and driveability is available in the MEDALION TOURING. The elegant, well defined appearance of MEDALION TOURING is mature, and matches the artistry of a tastefully built, highly tuned machine. Using the all new 'continuous strand' ADVANTEX packing material technology, MEDALION TOURING acheives extremely high levels of exhaust system efficiency, while maintaining a street driveable, extremely low frequency and deep tone that is well under 93db for discreet sports driving. This system requires no removeable silencer for under 93db operation at all rpms. The extremely deep, low frequency tone keeps in-cabin noise to a minimum. The full SUS304 stainless MEDALION TOURING features a slim-line oval canister, and a special dual wall, angle-cut tip. This premium quality system is for sports driving. AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains. Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU. AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Tuesday April 30th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Tanabe Medalian Exhaust - Medalion Touring: A refined level of performance and driveability is available in the MEDALION TOURING. The elegant, well defined appearance of MEDALION TOURING is mature, and matches the artistry of a tastefully built, highly tuned machine. Using the all new 'continuous strand' ADVANTEX packing material technology, MEDALION TOURING acheives extremely high levels of exhaust system efficiency, while maintaining a street driveable, extremely low frequency and deep tone that is well under 93db for discreet sports driving. This system requires no removeable silencer for under 93db operation at all rpms. The extremely deep, low frequency tone keeps in-cabin noise to a minimum. The full SUS304 stainless MEDALION TOURING features a slim-line oval canister, and a special dual wall, angle-cut tip. This premium quality system is for sports driving. AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains. Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU. AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Wednesday May 1st and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
HKS 370Z High Power cat-back: Inspired and designed from endurance and GT racing in Japan, HKS developed its Hi-Power Exhaust system for both turbocharged and naturally aspirated applications. HKS has incorporated this new race inspired offset muffler and piping design into many street applications, which offers a greater flow and higher-PRM power gains due to the less restrictive design. This is achieved by eliminating unnecessary bends for the straightest exhaust path. For turbocharged applications, the large and smooth exhaust flow allows greater exhaust velocity for better mid-range boost response and high-RPM power. Naturally aspirated vehicles also benefit from greater exhaust flow capacity as engine tuning levels increase. Certain applications are available in a Silent Hi-Power version which has an inner silencer built into the muffler. Like Drager Exhaust systems, Hi-Power Exhaust systems are made from SUS304 stainless steel muffler and tip assemblies. M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:
PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Thursday May 2nd and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
HKS 370Z High Power cat-back: Inspired and designed from endurance and GT racing in Japan, HKS developed its Hi-Power Exhaust system for both turbocharged and naturally aspirated applications. HKS has incorporated this new race inspired offset muffler and piping design into many street applications, which offers a greater flow and higher-PRM power gains due to the less restrictive design. This is achieved by eliminating unnecessary bends for the straightest exhaust path. For turbocharged applications, the large and smooth exhaust flow allows greater exhaust velocity for better mid-range boost response and high-RPM power. Naturally aspirated vehicles also benefit from greater exhaust flow capacity as engine tuning levels increase. Certain applications are available in a Silent Hi-Power version which has an inner silencer built into the muffler. Like Drager Exhaust systems, Hi-Power Exhaust systems are made from SUS304 stainless steel muffler and tip assemblies. M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:
PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Friday May 3rd and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
HKS 370Z High Power cat-back: Inspired and designed from endurance and GT racing in Japan, HKS developed its Hi-Power Exhaust system for both turbocharged and naturally aspirated applications. HKS has incorporated this new race inspired offset muffler and piping design into many street applications, which offers a greater flow and higher-PRM power gains due to the less restrictive design. This is achieved by eliminating unnecessary bends for the straightest exhaust path. For turbocharged applications, the large and smooth exhaust flow allows greater exhaust velocity for better mid-range boost response and high-RPM power. Naturally aspirated vehicles also benefit from greater exhaust flow capacity as engine tuning levels increase. Certain applications are available in a Silent Hi-Power version which has an inner silencer built into the muffler. Like Drager Exhaust systems, Hi-Power Exhaust systems are made from SUS304 stainless steel muffler and tip assemblies. M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:
PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Saturday May 4th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
HKS 370Z High Power cat-back: Inspired and designed from endurance and GT racing in Japan, HKS developed its Hi-Power Exhaust system for both turbocharged and naturally aspirated applications. HKS has incorporated this new race inspired offset muffler and piping design into many street applications, which offers a greater flow and higher-PRM power gains due to the less restrictive design. This is achieved by eliminating unnecessary bends for the straightest exhaust path. For turbocharged applications, the large and smooth exhaust flow allows greater exhaust velocity for better mid-range boost response and high-RPM power. Naturally aspirated vehicles also benefit from greater exhaust flow capacity as engine tuning levels increase. Certain applications are available in a Silent Hi-Power version which has an inner silencer built into the muffler. Like Drager Exhaust systems, Hi-Power Exhaust systems are made from SUS304 stainless steel muffler and tip assemblies. M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:
PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Monday May 6th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
HKS 370Z High Power cat-back: Inspired and designed from endurance and GT racing in Japan, HKS developed its Hi-Power Exhaust system for both turbocharged and naturally aspirated applications. HKS has incorporated this new race inspired offset muffler and piping design into many street applications, which offers a greater flow and higher-PRM power gains due to the less restrictive design. This is achieved by eliminating unnecessary bends for the straightest exhaust path. For turbocharged applications, the large and smooth exhaust flow allows greater exhaust velocity for better mid-range boost response and high-RPM power. Naturally aspirated vehicles also benefit from greater exhaust flow capacity as engine tuning levels increase. Certain applications are available in a Silent Hi-Power version which has an inner silencer built into the muffler. Like Drager Exhaust systems, Hi-Power Exhaust systems are made from SUS304 stainless steel muffler and tip assemblies. M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:
PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Tuesday May 7th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Borla 09+ 370z Catback Exhaust: BORLA Cat-Back exhausts feature patented, straight-through and multi-core technology to unleash hidden horsepower. Increased exhaust velocity adds power, driving excitement, fuel economy and the distinctive BORLA Sound of Power respected by motoring enthusiasts everywhere. Each system is built from premium austenitic stainless steel, superior to T-400 series knockoffs, to give you the absolute best in performance and durability. Ultra-smooth mandrel bends ensure maximum flow and power, and precision computer-controlled CNC manufacturing ensures an accurate fit. Best of all, BORLA stands behind every system with a Million-Mile Warranty. Just what you'd expect from the world's most experienced (and most winning) exhaust brand. K&N Cold Air Intake 2009-2011 Nissan 370Z 3.7L:Built for performance and show, the 69 Series Typhoon™ Air Intake System is a free-flowing mandrel-bent aluminum tube induction system designed to fit many sport compact performance vehicles. Typhoon intake tubes have a high quality finish that's made to last. K&N intake systems replace your vehicle's restrictive factory air filter and air intake housing. K&N intakes are designed to dramatically reduce intake restriction resulting in additional power and torque. All of them come with a Million Mile Limited Warranty and are guaranteed to increase horsepower. Not CARB Exempt for 370z application yet. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Thursday May 9th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Borla 09+ 370z Catback Exhaust: BORLA Cat-Back exhausts feature patented, straight-through and multi-core technology to unleash hidden horsepower. Increased exhaust velocity adds power, driving excitement, fuel economy and the distinctive BORLA Sound of Power respected by motoring enthusiasts everywhere. Each system is built from premium austenitic stainless steel, superior to T-400 series knockoffs, to give you the absolute best in performance and durability. Ultra-smooth mandrel bends ensure maximum flow and power, and precision computer-controlled CNC manufacturing ensures an accurate fit. Best of all, BORLA stands behind every system with a Million-Mile Warranty. Just what you'd expect from the world's most experienced (and most winning) exhaust brand. K&N Cold Air Intake 2009-2011 Nissan 370Z 3.7L:Built for performance and show, the 69 Series Typhoon™ Air Intake System is a free-flowing mandrel-bent aluminum tube induction system designed to fit many sport compact performance vehicles. Typhoon intake tubes have a high quality finish that's made to last. K&N intake systems replace your vehicle's restrictive factory air filter and air intake housing. K&N intakes are designed to dramatically reduce intake restriction resulting in additional power and torque. All of them come with a Million Mile Limited Warranty and are guaranteed to increase horsepower. Not CARB Exempt for 370z application yet. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
How much for the Stillen Gen 3 CAI 370Z? 78046
|
Quote:
Thank you for the inquiry! Thanks, Steven Watson StevenW@motionlabtuning.com |
It is Friday May 10th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Borla 09+ 370z Catback Exhaust: BORLA Cat-Back exhausts feature patented, straight-through and multi-core technology to unleash hidden horsepower. Increased exhaust velocity adds power, driving excitement, fuel economy and the distinctive BORLA Sound of Power respected by motoring enthusiasts everywhere. Each system is built from premium austenitic stainless steel, superior to T-400 series knockoffs, to give you the absolute best in performance and durability. Ultra-smooth mandrel bends ensure maximum flow and power, and precision computer-controlled CNC manufacturing ensures an accurate fit. Best of all, BORLA stands behind every system with a Million-Mile Warranty. Just what you'd expect from the world's most experienced (and most winning) exhaust brand. K&N Cold Air Intake 2009-2011 Nissan 370Z 3.7L:Built for performance and show, the 69 Series Typhoon™ Air Intake System is a free-flowing mandrel-bent aluminum tube induction system designed to fit many sport compact performance vehicles. Typhoon intake tubes have a high quality finish that's made to last. K&N intake systems replace your vehicle's restrictive factory air filter and air intake housing. K&N intakes are designed to dramatically reduce intake restriction resulting in additional power and torque. All of them come with a Million Mile Limited Warranty and are guaranteed to increase horsepower. Not CARB Exempt for 370z application yet. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Saturday May 11th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Borla 09+ 370z Catback Exhaust: BORLA Cat-Back exhausts feature patented, straight-through and multi-core technology to unleash hidden horsepower. Increased exhaust velocity adds power, driving excitement, fuel economy and the distinctive BORLA Sound of Power respected by motoring enthusiasts everywhere. Each system is built from premium austenitic stainless steel, superior to T-400 series knockoffs, to give you the absolute best in performance and durability. Ultra-smooth mandrel bends ensure maximum flow and power, and precision computer-controlled CNC manufacturing ensures an accurate fit. Best of all, BORLA stands behind every system with a Million-Mile Warranty. Just what you'd expect from the world's most experienced (and most winning) exhaust brand. K&N Cold Air Intake 2009-2011 Nissan 370Z 3.7L:Built for performance and show, the 69 Series Typhoon™ Air Intake System is a free-flowing mandrel-bent aluminum tube induction system designed to fit many sport compact performance vehicles. Typhoon intake tubes have a high quality finish that's made to last. K&N intake systems replace your vehicle's restrictive factory air filter and air intake housing. K&N intakes are designed to dramatically reduce intake restriction resulting in additional power and torque. All of them come with a Million Mile Limited Warranty and are guaranteed to increase horsepower. Not CARB Exempt for 370z application yet. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Monday May 13th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
2008-2012 370Z & G37 Invidia Gemini Catback: The Invidia Gemini catback exhaust system for the 2008-2012 G37 & 370Z sounds as good as it looks. A full true dual exhaust system, the Gemini features mandrel bent 60mm stainless steel piping and a free flowing oval style sport muffler to provide better exhaust flow for improved performance. Bolting up a Gemini to your VQ will allow your G37 coupe or 370Z's sonorous exhaust note to come through loud and clear when you want it to, without producing harsh or overly loud overtones during regular driving; the perfect choice for those who want great performance with an exhaust note that won't wake the dead. Consider the Gemini to be a quieter version of the Q300. HKS Race Suction Intake Kit Nissan 370Z 09-12: HKS Racing Suction Reloaded Kits have been developed as the leading intake system for high performance applications. Each kit features aluminum suction pipes that have been tested for optimal air flow. Included in each kit is HKS; Reloaded filter with its patented Super-Funnel and new technical advances: - Filter cage allows for 30% more intake surface area - Aluminum back plate for added strength - Sealing ring reduces contaminants from entering engine - Dual Density wet filter element Inlet size: 80mm Element size: 200mm PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Tuesday May 14th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
2008-2012 370Z & G37 Invidia Gemini Catback: The Invidia Gemini catback exhaust system for the 2008-2012 G37 & 370Z sounds as good as it looks. A full true dual exhaust system, the Gemini features mandrel bent 60mm stainless steel piping and a free flowing oval style sport muffler to provide better exhaust flow for improved performance. Bolting up a Gemini to your VQ will allow your G37 coupe or 370Z's sonorous exhaust note to come through loud and clear when you want it to, without producing harsh or overly loud overtones during regular driving; the perfect choice for those who want great performance with an exhaust note that won't wake the dead. Consider the Gemini to be a quieter version of the Q300. HKS Race Suction Intake Kit Nissan 370Z 09-12: HKS Racing Suction Reloaded Kits have been developed as the leading intake system for high performance applications. Each kit features aluminum suction pipes that have been tested for optimal air flow. Included in each kit is HKS; Reloaded filter with its patented Super-Funnel and new technical advances: - Filter cage allows for 30% more intake surface area - Aluminum back plate for added strength - Sealing ring reduces contaminants from entering engine - Dual Density wet filter element Inlet size: 80mm Element size: 200mm PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Wednesday May 15th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
2008-2012 370Z & G37 Invidia Gemini Catback: The Invidia Gemini catback exhaust system for the 2008-2012 G37 & 370Z sounds as good as it looks. A full true dual exhaust system, the Gemini features mandrel bent 60mm stainless steel piping and a free flowing oval style sport muffler to provide better exhaust flow for improved performance. Bolting up a Gemini to your VQ will allow your G37 coupe or 370Z's sonorous exhaust note to come through loud and clear when you want it to, without producing harsh or overly loud overtones during regular driving; the perfect choice for those who want great performance with an exhaust note that won't wake the dead. Consider the Gemini to be a quieter version of the Q300. HKS Race Suction Intake Kit Nissan 370Z 09-12: HKS Racing Suction Reloaded Kits have been developed as the leading intake system for high performance applications. Each kit features aluminum suction pipes that have been tested for optimal air flow. Included in each kit is HKS; Reloaded filter with its patented Super-Funnel and new technical advances: - Filter cage allows for 30% more intake surface area - Aluminum back plate for added strength - Sealing ring reduces contaminants from entering engine - Dual Density wet filter element Inlet size: 80mm Element size: 200mm PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Thursday May 16th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Berk Technology 370Z Dual 2.5" Exhaust: These days Nissan is making very good OEM exhaust systems leaving very little on the table when it comes to horsepower and torque. Thankfully the team at Berk Technology are experts when it comes making a good exhaust system a great exhaust systems. Backed by years of experience in building championship winning race cars, Berk Technology has applied the same knowledge into their line of street exhaust systems for the 370Z. The Berk Technology 370Z dual exhaust system was designed from the ground up as a no compromise system that unlocks the potential of the potent Nissan VQ37VHR motor. Through testing and R&D we discovered the most optimal X-pipe design which is unique to our product. Our design utilizes a tangential siamesed X-pipe design that proved to make the most power on the 370Z and is one of the secrets behind our wide power gains and clean sound. Once you install this system on your 370Z the first thing you'll notice is our signature sound. It will still keep the same sound character of the 370Z, but adds a slightly exotic note that is intoxicating to the automotive enthusiast. Another great benefit is that our systems are tuned to be near silent at cruise and will only come alive during heavier throttle application. There is zero intrusive cabin drone or unpleasant harshness. Vital Stats:
K&N Cold Air Intake 2009-2011 Nissan 370Z 3.7L:Built for performance and show, the 69 Series Typhoon™ Air Intake System is a free-flowing mandrel-bent aluminum tube induction system designed to fit many sport compact performance vehicles. Typhoon intake tubes have a high quality finish that's made to last. K&N intake systems replace your vehicle's restrictive factory air filter and air intake housing. K&N intakes are designed to dramatically reduce intake restriction resulting in additional power and torque. All of them come with a Million Mile Limited Warranty and are guaranteed to increase horsepower. Not CARB Exempt for 370z application yet. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Friday May 17th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Tanabe Medalian Exhaust - Medalion Touring: A refined level of performance and driveability is available in the MEDALION TOURING. The elegant, well defined appearance of MEDALION TOURING is mature, and matches the artistry of a tastefully built, highly tuned machine. Using the all new 'continuous strand' ADVANTEX packing material technology, MEDALION TOURING acheives extremely high levels of exhaust system efficiency, while maintaining a street driveable, extremely low frequency and deep tone that is well under 93db for discreet sports driving. This system requires no removeable silencer for under 93db operation at all rpms. The extremely deep, low frequency tone keeps in-cabin noise to a minimum. The full SUS304 stainless MEDALION TOURING features a slim-line oval canister, and a special dual wall, angle-cut tip. This premium quality system is for sports driving. AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains. Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU. AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Saturday May 18th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Tanabe Medalian Exhaust - Medalion Touring: A refined level of performance and driveability is available in the MEDALION TOURING. The elegant, well defined appearance of MEDALION TOURING is mature, and matches the artistry of a tastefully built, highly tuned machine. Using the all new 'continuous strand' ADVANTEX packing material technology, MEDALION TOURING acheives extremely high levels of exhaust system efficiency, while maintaining a street driveable, extremely low frequency and deep tone that is well under 93db for discreet sports driving. This system requires no removeable silencer for under 93db operation at all rpms. The extremely deep, low frequency tone keeps in-cabin noise to a minimum. The full SUS304 stainless MEDALION TOURING features a slim-line oval canister, and a special dual wall, angle-cut tip. This premium quality system is for sports driving. AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains. Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU. AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Monday May 20th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Tanabe Medalian Exhaust - Medalion Touring: A refined level of performance and driveability is available in the MEDALION TOURING. The elegant, well defined appearance of MEDALION TOURING is mature, and matches the artistry of a tastefully built, highly tuned machine. Using the all new 'continuous strand' ADVANTEX packing material technology, MEDALION TOURING acheives extremely high levels of exhaust system efficiency, while maintaining a street driveable, extremely low frequency and deep tone that is well under 93db for discreet sports driving. This system requires no removeable silencer for under 93db operation at all rpms. The extremely deep, low frequency tone keeps in-cabin noise to a minimum. The full SUS304 stainless MEDALION TOURING features a slim-line oval canister, and a special dual wall, angle-cut tip. This premium quality system is for sports driving. AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains. Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU. AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Tuesday May 21st and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Lite Speed Titanium Exhaust Nissan 370Z: Introducing Litespeed Racing’s all new full titanium race exhaust for Nissan 370z. This is a no-holds-barred, ultra-high performance exhaust system designed for track and street use. Its unique straight pipe design makes it one of the lightest and most aggressive systems on the market. Oversized rear resonators eliminate drone and keep sound levels down at street speeds, all while producing +14 peak horse power and +16 pound feet of torque over the NISMO exhaust. At only 14.2 pounds, it is 38 pounds less than stock. AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains. Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU. AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
How much for a stillen Gen 3 shipped to 78046?
Sent from my SPH-L710 using Tapatalk 2 |
Quote:
Thanks, Alex Goodwin AlexG@motionlabtuning.com |
It is Wednesday May 22nd and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
2008-2012 370Z & G37 Invidia Gemini Catback: The Invidia Gemini catback exhaust system for the 2008-2012 G37 & 370Z sounds as good as it looks. A full true dual exhaust system, the Gemini features mandrel bent 60mm stainless steel piping and a free flowing oval style sport muffler to provide better exhaust flow for improved performance. Bolting up a Gemini to your VQ will allow your G37 coupe or 370Z's sonorous exhaust note to come through loud and clear when you want it to, without producing harsh or overly loud overtones during regular driving; the perfect choice for those who want great performance with an exhaust note that won't wake the dead. Consider the Gemini to be a quieter version of the Q300. HKS Race Suction Intake Kit Nissan 370Z 09-12: HKS Racing Suction Reloaded Kits have been developed as the leading intake system for high performance applications. Each kit features aluminum suction pipes that have been tested for optimal air flow. Included in each kit is HKS; Reloaded filter with its patented Super-Funnel and new technical advances: - Filter cage allows for 30% more intake surface area - Aluminum back plate for added strength - Sealing ring reduces contaminants from entering engine - Dual Density wet filter element Inlet size: 80mm Element size: 200mm PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Thursday May 23rd and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
2008-2012 370Z & G37 Invidia Gemini Catback: The Invidia Gemini catback exhaust system for the 2008-2012 G37 & 370Z sounds as good as it looks. A full true dual exhaust system, the Gemini features mandrel bent 60mm stainless steel piping and a free flowing oval style sport muffler to provide better exhaust flow for improved performance. Bolting up a Gemini to your VQ will allow your G37 coupe or 370Z's sonorous exhaust note to come through loud and clear when you want it to, without producing harsh or overly loud overtones during regular driving; the perfect choice for those who want great performance with an exhaust note that won't wake the dead. Consider the Gemini to be a quieter version of the Q300. HKS Race Suction Intake Kit Nissan 370Z 09-12: HKS Racing Suction Reloaded Kits have been developed as the leading intake system for high performance applications. Each kit features aluminum suction pipes that have been tested for optimal air flow. Included in each kit is HKS; Reloaded filter with its patented Super-Funnel and new technical advances: - Filter cage allows for 30% more intake surface area - Aluminum back plate for added strength - Sealing ring reduces contaminants from entering engine - Dual Density wet filter element Inlet size: 80mm Element size: 200mm PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Friday May 24th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
2008-2012 370Z & G37 Invidia Gemini Catback: The Invidia Gemini catback exhaust system for the 2008-2012 G37 & 370Z sounds as good as it looks. A full true dual exhaust system, the Gemini features mandrel bent 60mm stainless steel piping and a free flowing oval style sport muffler to provide better exhaust flow for improved performance. Bolting up a Gemini to your VQ will allow your G37 coupe or 370Z's sonorous exhaust note to come through loud and clear when you want it to, without producing harsh or overly loud overtones during regular driving; the perfect choice for those who want great performance with an exhaust note that won't wake the dead. Consider the Gemini to be a quieter version of the Q300. HKS Race Suction Intake Kit Nissan 370Z 09-12: HKS Racing Suction Reloaded Kits have been developed as the leading intake system for high performance applications. Each kit features aluminum suction pipes that have been tested for optimal air flow. Included in each kit is HKS; Reloaded filter with its patented Super-Funnel and new technical advances: - Filter cage allows for 30% more intake surface area - Aluminum back plate for added strength - Sealing ring reduces contaminants from entering engine - Dual Density wet filter element Inlet size: 80mm Element size: 200mm PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Saturday May 25th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
HKS 370Z High Power cat-back: Inspired and designed from endurance and GT racing in Japan, HKS developed its Hi-Power Exhaust system for both turbocharged and naturally aspirated applications. HKS has incorporated this new race inspired offset muffler and piping design into many street applications, which offers a greater flow and higher-PRM power gains due to the less restrictive design. This is achieved by eliminating unnecessary bends for the straightest exhaust path. For turbocharged applications, the large and smooth exhaust flow allows greater exhaust velocity for better mid-range boost response and high-RPM power. Naturally aspirated vehicles also benefit from greater exhaust flow capacity as engine tuning levels increase. Certain applications are available in a Silent Hi-Power version which has an inner silencer built into the muffler. Like Drager Exhaust systems, Hi-Power Exhaust systems are made from SUS304 stainless steel muffler and tip assemblies. Injen Air Intake - SP Series Intake System: The Injen SP Series Intake Systems Feature the Patent Pending MR Technology Process for Optimal Gains and a Safe A/F Ratio. The Injen SP Series Intake System does not limit itself to just a Cold Air System or Short Ram System. The MR Technology process has its effects on both types. The Injen SP Series Intake is The World's First Tuned Intake System. For over a decade Injen Technology Co. Ltd and our sister company has played a major roll in the design and development of air intake systems. Injen Technology is based out of California in the same city and just a few miles away from the famous Pomona Winter Nationals Top Fuel Raceway. Injen Technology's history is a classic success story of a small manufacturing company turned industry leader of aftermarket performance products. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Tuesday May 28th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
HKS 370Z High Power cat-back: Inspired and designed from endurance and GT racing in Japan, HKS developed its Hi-Power Exhaust system for both turbocharged and naturally aspirated applications. HKS has incorporated this new race inspired offset muffler and piping design into many street applications, which offers a greater flow and higher-PRM power gains due to the less restrictive design. This is achieved by eliminating unnecessary bends for the straightest exhaust path. For turbocharged applications, the large and smooth exhaust flow allows greater exhaust velocity for better mid-range boost response and high-RPM power. Naturally aspirated vehicles also benefit from greater exhaust flow capacity as engine tuning levels increase. Certain applications are available in a Silent Hi-Power version which has an inner silencer built into the muffler. Like Drager Exhaust systems, Hi-Power Exhaust systems are made from SUS304 stainless steel muffler and tip assemblies. Injen Air Intake - SP Series Intake System: The Injen SP Series Intake Systems Feature the Patent Pending MR Technology Process for Optimal Gains and a Safe A/F Ratio. The Injen SP Series Intake System does not limit itself to just a Cold Air System or Short Ram System. The MR Technology process has its effects on both types. The Injen SP Series Intake is The World's First Tuned Intake System. For over a decade Injen Technology Co. Ltd and our sister company has played a major roll in the design and development of air intake systems. Injen Technology is based out of California in the same city and just a few miles away from the famous Pomona Winter Nationals Top Fuel Raceway. Injen Technology's history is a classic success story of a small manufacturing company turned industry leader of aftermarket performance products. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Wednesday May 29th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
HKS 370Z High Power cat-back: Inspired and designed from endurance and GT racing in Japan, HKS developed its Hi-Power Exhaust system for both turbocharged and naturally aspirated applications. HKS has incorporated this new race inspired offset muffler and piping design into many street applications, which offers a greater flow and higher-PRM power gains due to the less restrictive design. This is achieved by eliminating unnecessary bends for the straightest exhaust path. For turbocharged applications, the large and smooth exhaust flow allows greater exhaust velocity for better mid-range boost response and high-RPM power. Naturally aspirated vehicles also benefit from greater exhaust flow capacity as engine tuning levels increase. Certain applications are available in a Silent Hi-Power version which has an inner silencer built into the muffler. Like Drager Exhaust systems, Hi-Power Exhaust systems are made from SUS304 stainless steel muffler and tip assemblies. Injen Air Intake - SP Series Intake System: The Injen SP Series Intake Systems Feature the Patent Pending MR Technology Process for Optimal Gains and a Safe A/F Ratio. The Injen SP Series Intake System does not limit itself to just a Cold Air System or Short Ram System. The MR Technology process has its effects on both types. The Injen SP Series Intake is The World's First Tuned Intake System. For over a decade Injen Technology Co. Ltd and our sister company has played a major roll in the design and development of air intake systems. Injen Technology is based out of California in the same city and just a few miles away from the famous Pomona Winter Nationals Top Fuel Raceway. Injen Technology's history is a classic success story of a small manufacturing company turned industry leader of aftermarket performance products. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Thursday May 30th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
2008-2012 370Z & G37 Invidia Gemini Catback: The Invidia Gemini catback exhaust system for the 2008-2012 G37 & 370Z sounds as good as it looks. A full true dual exhaust system, the Gemini features mandrel bent 60mm stainless steel piping and a free flowing oval style sport muffler to provide better exhaust flow for improved performance. Bolting up a Gemini to your VQ will allow your G37 coupe or 370Z's sonorous exhaust note to come through loud and clear when you want it to, without producing harsh or overly loud overtones during regular driving; the perfect choice for those who want great performance with an exhaust note that won't wake the dead. Consider the Gemini to be a quieter version of the Q300. HKS Race Suction Intake Kit Nissan 370Z 09-12: HKS Racing Suction Reloaded Kits have been developed as the leading intake system for high performance applications. Each kit features aluminum suction pipes that have been tested for optimal air flow. Included in each kit is HKS; Reloaded filter with its patented Super-Funnel and new technical advances: - Filter cage allows for 30% more intake surface area - Aluminum back plate for added strength - Sealing ring reduces contaminants from entering engine - Dual Density wet filter element Inlet size: 80mm Element size: 200mm PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Friday May 31st and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
2008-2012 370Z & G37 Invidia Gemini Catback: The Invidia Gemini catback exhaust system for the 2008-2012 G37 & 370Z sounds as good as it looks. A full true dual exhaust system, the Gemini features mandrel bent 60mm stainless steel piping and a free flowing oval style sport muffler to provide better exhaust flow for improved performance. Bolting up a Gemini to your VQ will allow your G37 coupe or 370Z's sonorous exhaust note to come through loud and clear when you want it to, without producing harsh or overly loud overtones during regular driving; the perfect choice for those who want great performance with an exhaust note that won't wake the dead. Consider the Gemini to be a quieter version of the Q300. HKS Race Suction Intake Kit Nissan 370Z 09-12: HKS Racing Suction Reloaded Kits have been developed as the leading intake system for high performance applications. Each kit features aluminum suction pipes that have been tested for optimal air flow. Included in each kit is HKS; Reloaded filter with its patented Super-Funnel and new technical advances: - Filter cage allows for 30% more intake surface area - Aluminum back plate for added strength - Sealing ring reduces contaminants from entering engine - Dual Density wet filter element Inlet size: 80mm Element size: 200mm PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Tuesday June 4th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
2008-2012 370Z & G37 Invidia Gemini Catback: The Invidia Gemini catback exhaust system for the 2008-2012 G37 & 370Z sounds as good as it looks. A full true dual exhaust system, the Gemini features mandrel bent 60mm stainless steel piping and a free flowing oval style sport muffler to provide better exhaust flow for improved performance. Bolting up a Gemini to your VQ will allow your G37 coupe or 370Z's sonorous exhaust note to come through loud and clear when you want it to, without producing harsh or overly loud overtones during regular driving; the perfect choice for those who want great performance with an exhaust note that won't wake the dead. Consider the Gemini to be a quieter version of the Q300. HKS Race Suction Intake Kit Nissan 370Z 09-12: HKS Racing Suction Reloaded Kits have been developed as the leading intake system for high performance applications. Each kit features aluminum suction pipes that have been tested for optimal air flow. Included in each kit is HKS; Reloaded filter with its patented Super-Funnel and new technical advances: - Filter cage allows for 30% more intake surface area - Aluminum back plate for added strength - Sealing ring reduces contaminants from entering engine - Dual Density wet filter element Inlet size: 80mm Element size: 200mm PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Wednesday June 5th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Berk Technologies 370Z/G37 High Flow Catalytic Converters: Metallic substrate spun catalytic converters, OBDII & 49 state compliant. Full stainless steel construction. Metallic substrate offers higher flow and lighter weight. Uses advanced spiral wound ultra thin foil. Includes our custom made soft crush graphite collector gaskets for a leak free seal. These are made specifically for the new HR motor by BERK. Made with pride in the USA. Fits VQ35HR & VQ37HR Motors:
M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:
PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Thursday June 6th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Berk Technologies 370Z/G37 High Flow Catalytic Converters: Metallic substrate spun catalytic converters, OBDII & 49 state compliant. Full stainless steel construction. Metallic substrate offers higher flow and lighter weight. Uses advanced spiral wound ultra thin foil. Includes our custom made soft crush graphite collector gaskets for a leak free seal. These are made specifically for the new HR motor by BERK. Made with pride in the USA. Fits VQ35HR & VQ37HR Motors:
M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:
PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Saturday June 8th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Berk Technologies 370Z/G37 High Flow Catalytic Converters: Metallic substrate spun catalytic converters, OBDII & 49 state compliant. Full stainless steel construction. Metallic substrate offers higher flow and lighter weight. Uses advanced spiral wound ultra thin foil. Includes our custom made soft crush graphite collector gaskets for a leak free seal. These are made specifically for the new HR motor by BERK. Made with pride in the USA. Fits VQ35HR & VQ37HR Motors:
M7 T-Titan Catback: The M7 brand was conceived with one simple objective – to create the ultimate in high quality performance enhancing automotive products. All M7 products are researched, developed and manufactured in Japan using the latest technology and then distributed worldwide for rigorous testing under various conditions. M7 products are also tested by M7 Co. Ltd, Japan's factory racing operations and Team M7's professional racing drivers to deliver the ultimate automotive products available. Some of the highlights of this high end exhaust are:
PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
It is Tuesday June 11th and Motion Lab Tuning is your go to place for your bolt on 370z performance. Here are a few other great products you can contact us about.
Tanabe Medalian Exhaust - Medalion Touring: A refined level of performance and driveability is available in the MEDALION TOURING. The elegant, well defined appearance of MEDALION TOURING is mature, and matches the artistry of a tastefully built, highly tuned machine. Using the all new 'continuous strand' ADVANTEX packing material technology, MEDALION TOURING acheives extremely high levels of exhaust system efficiency, while maintaining a street driveable, extremely low frequency and deep tone that is well under 93db for discreet sports driving. This system requires no removeable silencer for under 93db operation at all rpms. The extremely deep, low frequency tone keeps in-cabin noise to a minimum. The full SUS304 stainless MEDALION TOURING features a slim-line oval canister, and a special dual wall, angle-cut tip. This premium quality system is for sports driving. AEM ETI Intake System: Once again AEM is raising engineering standards with an all new series of innovative air intake systems. With a revolutionary ETI module and fully integrated design, we have eliminated the need to detune or stage an intake tube diameter as it crosses the MAF sensor. The sensor is electronically adjusted to read proper air density instead of using physical tube designs intended to “trick” the MAF reading. The result is bigger horsepower and torque gains. Most modern fuel injected cars use a Mass Air flow (MAF) sensor to determine the air flow rate into the engine and meter fuel according to input from the sensor. The relation between the voltage output of the sensor and mass air flow is adversely affected by a shift to a larger diameter intake tube because the airspeed is reduced. This causes the MAF sensor to “under report” air flow causing a lean condition at worst and a Check Engine Light at best. To accommodate MAF sensor reporting, many intake systems reduce the diameter of the intake tube near the MAF sensor to stock or near stock size because of the need to maintain the correct air speed for the sensor to report the correct flow rate to the ECU. AEM's ETI Intake System is an alternative design approach that allows the intake tube to maintain its diameter resulting in more air flow into the throttle body. The ETI Intake System allows AEM to tune an engine for even more power by avoiding any tube down-sizing that will reduce overall airflow and horsepower. Instead the ETI electronically communicates with the MAF sensor to ensure an accurate amount of fuel is being delivered even though the tube is larger in size than the stock system. This means the vehicle maintains the calibration as intended by the factory while enjoying the benefits of our custom designed aftermarket intake system. PM, call, or E-mail for most up to date pricing! Other parts available such as Stainless steel brake lines from StopTech performance and Goodridge. High temp brake fluid available from MOTUL, ATE, and StopTech. We are open Monday - Friday 9AM EST to 6PM EST and Saturdays 10AM to 1PM. You can contact us via forum messaging, E-mail, and telephone. As always if you don't see it, just ask! Follow whats going on at the shop on our Facebook page Motion Lab Tuning - Automotive - Charlotte, NC | Facebook Thanks for looking! Alex Goodwin AlexG@motionlabtuning.com MotionLabTuning.com - Engineering Performance |
| All times are GMT -5. The time now is 01:58 PM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2