Nissan 370Z Forum - Z1 Motorsports: 370Z / G37 Cold Air Intake Kit $448

Nissan 370Z Forum (http://www.the370z.com/)

- Exhaust/Intake (http://www.the370z.com/exhaust-intake/)

- - Z1 Motorsports: 370Z / G37 Cold Air Intake Kit $448 (http://www.the370z.com/exhaust-intake/109202-z1-motorsports-370z-g37-cold-air-intake-kit-448-a.html)

Z1 Motorsports: 370Z / G37 Cold Air Intake Kit $448

Z1 Motorsports 370Z / G37 Cold Air Intake Kit

The Z1 Motorsports VQ37VHR Cold air intake for dual throttle body cars provides improved flow and a cooler denser air charge resulting in greater combustion efficiency and more power. Significant gains in power and response have been proven with this torture tested intake.

https://www.z1motorsports.com/images...Z370Z-3235.JPG

The new intake uses race proven technology by including two specially designed large media air filters with integrated velocity stacks for increased air flow. A velocity stack is designed to maximize and optimize air flow by allowing air to gently enter the intake piping through an un-obstructed rounded taper (similar to a trumpet horn.) This results in less intake turbulence and increased air velocity, allowing your intake system to work at it's maximum potential!

https://www.z1motorsports.com/imageG...city+Stack.jpg

https://www.z1motorsports.com/images...Z370Z-3257.JPG

While every cars result may differ depending on mods and tune, Z1 Motorsports was able to achieve an increased 10whp and and additional 10lb-ft of torque in house on a car previously equipped with just a Full Tomei Expreme Ti Exhaust. No re-tune was performed to achieve these results! You can expect even greater results when re-tune is performed.

https://www.z1motorsports.com/images...Z370Z-3253.JPG

Intake Kit Includes:

(2) Aluminum Intake Hard Pipes
(2) Silicone Straight Reducer Hose
(2) Silicone Throttle Body to Hard Pipe Adapter
(2) Aluminum 90° Hose to Filter Adapter
(2) Z1 High Flow Velocity Stack Air Filters
(1) Z1 Silicone Side PCV Breather Hose Set
(10) Intake Coupler Clamps
(1) Intake Installation Instructions

To Purchase Your Order Please Click Here!

Is the cut out required similar to the Stillen intakes?

Any deals going on for black friday?

Was going to pull the plug on some stillen intakes but now I may have changed my mind

Quote:

Originally Posted by VDesi07 (Post 3353511)

Is the cut out required similar to the Stillen intakes?

Any deals going on for black friday?

Was going to pull the plug on some stillen intakes but now I may have changed my mind

Not cutting for these and be sure to check out our Black Friday post!

This may sound stupid, but do they make the same power as the stillens or about the same? I'm ready to max out my credit cards this black friday. BTW that's SolidWorks right?

When will you have a dyno vs stock and gen3s? Considering switching from Gen3s to this but need more data.

Quote:

Originally Posted by derraj06 (Post 3354567)

When will you have a dyno vs stock and gen3s? Considering switching from Gen3s to this but need more data.

Hopefully next week after we recover from the holiday sale.

We performed back to back testing against Stillen Gen 3 and they were with in 1-2hp of each other one each run. The Z1 intake did make more top end on the 10th dyno run than the Stillen system on it's 10th pull.

Awaiting the restocking of the polished version. Any pics of the black with red/blue silicone?

What's the inner diameter?

those would look great powdercoated

I have the black/blue silicone. I'll snap a pic and update

Those are great pics and helped a lot for reference! Thanks!