Nissan 370Z Forum - Need someone to do me a favor

Page 2 of 2

Show 40 post(s) from this thread on one page

Nissan 370Z Forum (http://www.the370z.com/)

- Engine & Drivetrain (http://www.the370z.com/engine-drivetrain/)

- - Need someone to do me a favor (http://www.the370z.com/engine-drivetrain/82619-need-someone-do-me-favor.html)

Megan370z

11-26-2013 02:49 PM

Quote:

Originally Posted by 1slow370 (Post 2584008)

I shall take you up on that, You would probably need to disconnect both your ecus, and if you could just make a little list of what does or doesn't work that would be great.

I tested it with both ECUs completely disconnected and as far as my Z is, everything work beside starting the engine ofcourse.
This is with the key in my pocket.

without the key. there is no way of having the system to ON since the BCM is looking for the key.
unless I do my NATS hack from last spring which I could steal my own car in less than 5mins without any keys.

hope thats help you.

1slow370

11-26-2013 02:55 PM

Wipers and everything? Sweet.

Sent from my HTCONE using Tapatalk

Megan370z

11-26-2013 03:07 PM

Quote:

Originally Posted by 1slow370 (Post 2584283)

Wipers and everything? Sweet.

Sent from my HTCONE using Tapatalk

Oups I missed the wiper/washer motor but I see no reason why it wouldn't work since everything else BCM related items work.

I must add that I cant know at 100% about the 3 gauge pods since I don't have those OEM anymore...

the only problem on that OEM 3 gauge pods is the oil tempthat might not work. I think if I remember correctly it read the oil temp by CAN with the ECU.

1slow370

11-26-2013 03:15 PM

Great. I wonder if it works if u disconnect the main guage cluster.

Sent from my HTCONE using Tapatalk

1slow370

11-26-2013 04:28 PM

With the key you can get it to the on position right? So iwould just need to put in an aftermarket push start module then for cranking, and new guages.

phunk

11-26-2013 04:30 PM

manually wire fuel pump, since it shuts off the pump if it doesnt see a running engine

well.. most likely anyway. never checked on this car, but most cars do that now.

Megan370z

11-26-2013 04:59 PM

Quote:

Originally Posted by 1slow370 (Post 2584491)

With the key you can get it to the on position right? So iwould just need to put in an aftermarket push start module then for cranking, and new guages.

Btw... whats your plan ?

Hr head or a different swap ?

What i said with and without the key is still right ... with key everything bcm related items work and without it .. cant put it to ON

If you do the hr head . You dont need an aftermarket push start buttom.
I havent tested the oil temp gauge with the hr/vhr ecu setup since I didnt installed the sensor. But the clock and battery gauge still worked untill I smashed the unit.

1slow370

11-26-2013 05:38 PM

V8 with standalone. Already figured i was going to lose it. I found a module that should work in parallel wih factory bcm and give me starter relay trigger.

Sent from my HTCONE using Tapatalk

1slow370

11-26-2013 05:41 PM

Good point about the fuel pump but he new ecu has fuel pump control.

Sent from my HTCONE using Tapatalk

1slow370

11-26-2013 06:52 PM

Also the a/c compressor will need to be turned on by the new ecu.

All times are GMT -5. The time now is 11:25 PM.

Page 2 of 2

Show 40 post(s) from this thread on one page