how much are the extenders? I forget, but you can adjust the front dampening settings through the engine bay right?
http://img833.imageshack.us/img833/3...rstopstrut.jpg ^this is without the extenders correct? sorry if this was mentioned already, but couldn't you cut a hole in the black panels and then make some sort of cap out of the piece you remove so its accessible? oh yea and how much was the total install of the coilovers, camber arms, and allignment? Thanks. REP for the review |
Why not trim the extenders down to a shorter length? AFAIK, it's just a rigid rubber tube. The extenders just wrap around the top adjustment knob.
|
Quote:
Quote:
Actually the cap is what im thinking now, that is without extenders yes. You could also do what Daleks is suggesting and cut the extender its self down so it goes through the hole you drill and then sits right outside the interior piece so you dont have to worry about tying it down. Either would look sharp i think. Total install for coils and the camber arms was only 4 hours i believe and that included some adjustment and the swap back to shorter springs. Non Stop Tuning in Houston charges $75 an hour so $300 or so...The alignment was done later and it was $50 bucks. It was kind of hard for me to estimate time tho because they put all the mods i listed on the front page in at once so i just paid one large bill. @ Daleks --- its not a rigid rubber tube, it is spun metal inside, that said, i like the idea. Im waiting to see how much of my interior is going to have to come out when i get the cage done tho before i worry about it. |
Quote:
|
Quote:
Quote:
|
Quote:
Im almost positive that the front is the sway bar but its already greased. The rear is drive train related. Only heard at speeds under 40, the noise moves from left to right or right to left as i turn or goes away as i hit the gas. Secret Service Auto and Non Stop Tuning both took a look at it and everything is on the car right, its just something with the drive train. |
so which way do u think its easier to adjust the rear stiffness? Taking out the wheel and dropping the suspension or taking out the interior pieces?
|
Quote:
Its easy, take a look in the back, you will see 4 plastic tabs with little D rings on them , pull those out, then pull out the 2 mats and the plastic shield below them. Then you gently pull on the center back piece and you will find a number of tabs you can slip a flat head screwdriver down to pop off the car with. Once you have that out, you will have to disconnect the light, and then gently pull on the 2 side pieces and find their tabs, pop them free with the screw driver, and your good. It takes me about 2 min or so do do it carefully after i figured out where the tabs were the first time. Just take your time with it and you will be fine, If for some reason one of the plastic tabs breaks you should be able to pull it off the pannel and get a replacement tab from your local dealer. Hope this helps!! |
^^ helped a lot! Thx man...
I set mine at 20 front and 20 rear but i think the rear needs to be softer |
Quote:
|
You can cut the extenders I've done it. However I really want to find a plastic plug and make the hole big enough to fit my fingers in. Want it to look more OEM. Since I already drilled a hole in 1 side I'm fkd. But if i could do it all over again. I'd leave it alone and remove panels when need be.
|
This is how I did mine this weekend. 3/4 hole will fit the extender perfectly and cut the cable to about half an inch and there you have it. I still want to find plugs about 1.5" in diameter and make a hole big enough for me to adjust it that way and hide it when not being used with the plugs.
http://i934.photobucket.com/albums/a...s/IMG_1062.jpg |
Nice job! Looks really clean!
I didn't know the extenders could be trimmed like that. Might do the same with mine. Hiding them with plugs is a good option as well. Wouldn't want somebody absentmindedly twirling the knobs. |
Super clean! Nice work. I tried to do something similar but it didn't work out nearly as well for me so I just cut holes big enough to stick my fingers in and adjust haha.
|
What does everyone have there dampening set at? I keep playing around with the settings. Is there any problems with constantly changing the settings?
|
All times are GMT -5. The time now is 01:10 AM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2