Nissan 370Z Forum
Page 5 of 8 « First 34 5 67 Last »
Show 40 post(s) from this thread on one page

Nissan 370Z Forum (http://www.the370z.com/)
-   Body Interior/Exterior (http://www.the370z.com/body-interior-exterior/)
-   -   NEW! ZSpeed Performance V2 Aluminum Engine Splash Shields! (http://www.the370z.com/body-interior-exterior/52093-new-zspeed-performance-v2-aluminum-engine-splash-shields.html)

Joe@ZSpeed 06-21-2016 09:41 AM
Bump!

Joe@ZSpeed 08-16-2016 12:51 PM
Bump!

Joe@ZSpeed 09-02-2016 12:42 PM
Bump!

BobbyLight 09-02-2016 03:02 PM
I hit an unpainted speed bump at speed, and it tore the splash shield off. I never bought a new one as it also sheared off most of the bolt/clip holes on the car itself that secures the shield. Would this aluminum plate work, or does it utilize the same holes as the stock plastic shield?

Joe@ZSpeed 09-06-2016 09:02 AM
Quote:
Originally Posted by BobbyLight (Post 3547343)
I hit an unpainted speed bump at speed, and it tore the splash shield off. I never bought a new one as it also sheared off most of the bolt/clip holes on the car itself that secures the shield. Would this aluminum plate work, or does it utilize the same holes as the stock plastic shield?
It uses the same holes as the factory one, If the ends of the slots are just torn out it will normally still work as the u nuts pinch the bumper on the sides. If the tabs are just gone you wont have much to attach it to.

Joe@ZSpeed 09-22-2016 02:35 PM
Bump!

Joe@ZSpeed 10-14-2016 01:18 PM
Bump!

Joe@ZSpeed 12-13-2016 10:52 AM
Bump!

Joe@ZSpeed 01-11-2017 11:49 AM
Bump!

Jayhovah 01-11-2017 11:51 AM
Have you or any of your customers installed this in conjunction with the Gamma oil pan?
My OEM shield is getting pretty beat up and will need replacement in the near future.

Joe@ZSpeed 01-11-2017 12:05 PM
Quote:
Originally Posted by Jayhovah (Post 3601151)
Have you or any of your customers installed this in conjunction with the Gamma oil pan?
My OEM shield is getting pretty beat up and will need replacement in the near future.
So long as the pan doesn't hang down lower than the X-Member this should clear perfectly fine. We leave alot of room between the pan and shield.

Jayhovah 01-11-2017 12:14 PM
Quote:
Originally Posted by Joe@ZSpeed (Post 3601155)
So long as the pan doesn't hang down lower than the X-Member this should clear perfectly fine. We leave alot of room between the pan and shield.
Good to know!!!! Is there any flexibility to move the access hatch? Or even remove it completely?

Thanks for the responses.

Joe@ZSpeed 01-11-2017 12:34 PM
Quote:
Originally Posted by Jayhovah (Post 3601167)
Good to know!!!! Is there any flexibility to move the access hatch? Or even remove it completely?

Thanks for the responses.
Oil access door can be taken off, It is just a slotted fitment, Easily removed, 2 bolts.

Jayhovah 01-11-2017 12:43 PM
Quote:
Originally Posted by Joe@ZSpeed (Post 3601177)
Oil access door can be taken off, It is just a slotted fitment, Easily removed, 2 bolts.
Sorry I meant no hole/door for access at all.

Joe@ZSpeed 01-11-2017 01:04 PM
Quote:
Originally Posted by Jayhovah (Post 3601187)
Sorry I meant no hole/door for access at all.
No, They all come with the hole/door.


All times are GMT -5. The time now is 11:45 PM.
Page 5 of 8 « First 34 5 67 Last »
Show 40 post(s) from this thread on one page

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
Search Engine Optimization by vBSEO 3.6.0 PL2