Nissan 370Z Forum - NEW! ZSpeed Performance V2 Aluminum Engine Splash Shields!

Page 2 of 3

Show 40 post(s) from this thread on one page

Nissan 370Z Forum (http://www.the370z.com/)

- Body Interior/Exterior (http://www.the370z.com/body-interior-exterior/)

- - NEW! ZSpeed Performance V2 Aluminum Engine Splash Shields! (http://www.the370z.com/body-interior-exterior/52093-new-zspeed-performance-v2-aluminum-engine-splash-shields.html)

Stailey

05-25-2015 10:44 PM

Shipped to 11103?

Joe@ZSpeed

05-26-2015 10:07 AM

Can be ordered off the site, Should be about $15-20 for ship.
ZSpeed Performance Aluminum Engine Splash Shield 370Z Nissan

Joe@ZSpeed

06-05-2015 11:22 AM

Bump! In Stock!

Joe@ZSpeed

06-17-2015 08:16 AM

Bump!

68cam454

06-20-2015 10:32 PM

Is there a Nismo V2?

Joe@ZSpeed

06-22-2015 09:19 AM

Quote:

Originally Posted by 68cam454 (Post 3234802)

Is there a Nismo V2?

No V2 with the Nismo, We made a few minor updates to it but nothing major.

PharmDZ

11-06-2015 09:13 PM

Is there a way I'd be able to tell the V1 versus the V2? I just installed a hotchkis sway bar and have some issues with clearance of the grease fittings at the top of the sway bar bushings (had to take them off to fit the undershroud back on which I'm sure isn't a great idea).

Joe@ZSpeed

11-06-2015 10:16 PM

Quote:

Originally Posted by PharmDZ (Post 3342737)

The v2 has a section at the rear that is bent under, the v1 will be completely flat
From the middle back. The grease fitting can be removed if they interfere, not something that has to stay in.

Joe@ZSpeed

12-07-2015 09:39 AM

Bumped!

Joe@ZSpeed

12-12-2015 02:19 PM

Bump!

Joe@ZSpeed

12-14-2015 12:02 PM

Bump!

Joe@ZSpeed

01-04-2016 12:59 PM

Bump!

Joe@ZSpeed

02-22-2016 11:40 AM

Bump!

Joe@ZSpeed

02-27-2016 02:01 PM

Bump!

ColemanLee09

03-01-2016 12:23 AM

PM'ed you.

Joe@ZSpeed

03-15-2016 02:56 PM

Bump!

Joe@ZSpeed

06-02-2016 10:57 AM

Bump!

Blue06Z

06-02-2016 05:41 PM

Is there an ETA for '15/'16 NISMO?

Joe@ZSpeed

06-03-2016 09:42 AM

Quote:

Originally Posted by Blue06Z (Post 3491505)

Is there an ETA for '15/'16 NISMO?

3 Months ago!

ZSpeed Performance Nissan 300ZX 350Z 370Z Infiniti G35 G37 Q50 Q60

Blue06Z

06-03-2016 04:25 PM

Quote:

Originally Posted by Joe@ZSpeed (Post 3491863)

3 Months ago!

ZSpeed Performance Nissan 300ZX 350Z 370Z Infiniti G35 G37 Q50 Q60

Guess I forgot how to read yesterday.

Joe@ZSpeed

06-21-2016 09:41 AM

Bump!

Joe@ZSpeed

08-16-2016 12:51 PM

Bump!

Joe@ZSpeed

09-02-2016 12:42 PM

Bump!

BobbyLight

09-02-2016 03:02 PM

I hit an unpainted speed bump at speed, and it tore the splash shield off. I never bought a new one as it also sheared off most of the bolt/clip holes on the car itself that secures the shield. Would this aluminum plate work, or does it utilize the same holes as the stock plastic shield?

Joe@ZSpeed

09-06-2016 09:02 AM

Quote:

Originally Posted by BobbyLight (Post 3547343)

It uses the same holes as the factory one, If the ends of the slots are just torn out it will normally still work as the u nuts pinch the bumper on the sides. If the tabs are just gone you wont have much to attach it to.

Joe@ZSpeed

09-22-2016 02:35 PM

Bump!

Joe@ZSpeed

10-14-2016 01:18 PM

Bump!

Joe@ZSpeed

12-13-2016 10:52 AM

Bump!

Joe@ZSpeed

01-11-2017 11:49 AM

Bump!

Jayhovah

01-11-2017 11:51 AM

Have you or any of your customers installed this in conjunction with the Gamma oil pan?
My OEM shield is getting pretty beat up and will need replacement in the near future.

Joe@ZSpeed

01-11-2017 12:05 PM

Quote:

Originally Posted by Jayhovah (Post 3601151)

Have you or any of your customers installed this in conjunction with the Gamma oil pan?
My OEM shield is getting pretty beat up and will need replacement in the near future.

So long as the pan doesn't hang down lower than the X-Member this should clear perfectly fine. We leave alot of room between the pan and shield.

Jayhovah

01-11-2017 12:14 PM

Quote:

Originally Posted by Joe@ZSpeed (Post 3601155)

So long as the pan doesn't hang down lower than the X-Member this should clear perfectly fine. We leave alot of room between the pan and shield.

Good to know!!!! Is there any flexibility to move the access hatch? Or even remove it completely?

Thanks for the responses.

Joe@ZSpeed

01-11-2017 12:34 PM

Quote:

Originally Posted by Jayhovah (Post 3601167)

Good to know!!!! Is there any flexibility to move the access hatch? Or even remove it completely?

Thanks for the responses.

Oil access door can be taken off, It is just a slotted fitment, Easily removed, 2 bolts.

Jayhovah

01-11-2017 12:43 PM

Quote:

Originally Posted by Joe@ZSpeed (Post 3601177)

Oil access door can be taken off, It is just a slotted fitment, Easily removed, 2 bolts.

Sorry I meant no hole/door for access at all.

Joe@ZSpeed

01-11-2017 01:04 PM

Quote:

Originally Posted by Jayhovah (Post 3601187)

Sorry I meant no hole/door for access at all.

No, They all come with the hole/door.

Joe@ZSpeed

01-27-2017 09:14 AM

In Stock!

Joe@ZSpeed

03-23-2017 10:50 AM

Bump!

Nixin

03-30-2017 01:51 PM

Hi Joe. Does anyone in Toronto area carry the Z engine splash guard or is it a special order item through you directly? Thanks.

Joe@ZSpeed

03-30-2017 02:17 PM

Quote:

Originally Posted by Nixin (Post 3634347)

Hi Joe. Does anyone in Toronto area carry the Z engine splash guard or is it a special order item through you directly? Thanks.

We do not have a distributor in Canada, Shipping Postal is $60 to you.

Nixin

03-30-2017 02:42 PM

Thanks Joe. I will reach out to you soon and get my order in. Cheers.

Quote:

Originally Posted by Joe@ZSpeed (Post 3634356)

We do not have a distributor in Canada, Shipping Postal is $60 to you.

All times are GMT -5. The time now is 07:23 AM.

Page 2 of 3

Show 40 post(s) from this thread on one page