1 more stupid question. Do I need to predrill my bumper for the holes, or do I just stick it on then just hand tighten the screws in?

Just screwed the screws in. I would advise you to try the hole for the clip under the fog light and possibly widen it? My clip doenst' go in anymore.

Cool thanks for the tip! I'm gonna put it on tomorrow!

You are suppose to put the BOLT in there, There is a bolt and screw that goes into that hole.

Oh for real? Thank I didn't know. I didn't get one of those haha. I guess I'll go to a hardware store and buy one.

Got mine on tonight, I like it! Thanks! However that center bolt just falls out, so I guess I'll just go without it, unless someone knows the exact size:)

I'm gonna readjust mine tomorrow over lunch the on the driver side (your passenger side) Keeps slipping off, Gonna add a little more tape to that side.

I'm also gonna try to but a bolt in the center, Hate1 if I figure out one that works i'll let you know what size i used.

For the guys that have installed this, did it slip on over the exhaust tips, or did you need to remove them to install it? Specifically F.I. Exhaust Tips??

That's my only hesitation with this. And confirm it just slips over the Fog Light, I don't need to remove the foglight prior to putting this on?

Thanks!

Alright guys here some tips for the rear diffuser:
When you put the 3m tape on the rear diffuser line it up as close as possible to the outer edges on the top, I would suggest doubling (sticking another piece over the existing exposed piece) around the exhaust areas, where it curves around on both sides. If possible, I would suggest the stronger double sided tape mentioned in another thread, I don't know the part number?
~also heat up the carbon piece with the tape on it as well as the surface of the vehicle, i used a space heater, 15 mins before, 20 mins after It was put on with me applying pressure.
~there are 2 screws that need to be hand screwed in, for those of you worried about the damage done to the body, DON'T, these holes are located way inside and are unnoticeable, as well as very small, in fact if you don't like the diffuser for some reason, I don't see a problem taking it off, there will be no visible evidence that it once was there. As long as you can get the tape residue off.
~still waiting on the info for the center bolt, however it does feel secure enough to leave it off
~if you have exhaust tips that are close to the rear bumper, do not get this as it will most likely touch and ruin the diffuser, possibly cause vibrations as well. I do have a berk cbe which fits perfectly around.

Hope these tips help:)

Oh and it slips over both the fog light and exhausts, no need to remove any pieces.

I'm wondering since I have the F.I. exhaust will it bump/rub/melt :ugh:

But you said the Berks cleared no prob? cool cool

some pics of mine, and a shot for you XwchriswX you be the judge if it will fit or not:)
http://i884.photobucket.com/albums/a...3/e6950c5f.jpg
http://i884.photobucket.com/albums/a...3/0d2f380c.jpg
http://i884.photobucket.com/albums/a...3/6c54883b.jpg
http://i884.photobucket.com/albums/a...3/5404c12f.jpg

The bolt is suppose to screw into a nut on top and then you tighten it!

Thanks Hated1, looks like it will have enough clearance. I'm crossin my fingers! lol :tup:

I got the bolt but no nut, found a nut, now life is good!

Very Nice, once I get my wheel & tire package taken care of, this will be the next mod!!:tup:

im a little hesitant whether i should pull the trigger on this or not. Can anyone post some shots from the side and angles from farther back from the car.

Free shipping is still good to go. In stock!

I know it is mentioned somewhere on the thread about fitment with FI TDX. But has anyone actually tried if it fits? And is shipping still free Jay? :icon17:

Yes, it is. Still have few spots left. Totally forgot about this sale.

Is this deal still up and do we have a definite answer regarding the fitment with a FI exhaust??

Yes, but only FRP black in stock.

i want cf!
When are you getting more on carbon fiber?

sometime next week. I have people paid and waiting

Can I get on that CF list. Or at least how long would the wait be if I put the money Dow. Today?

I should have some coming in this week.

PM me for CF ones @ GB price
thanks

I'll post here when comes in.

Are you making a new carbon fiber piece that fits better?

Pmed shipped to canada in CF.

thx.

plz update when the CF ones are available again

What is the issue with the FI exhasut because that is what I got and I wnat the black FRP diffuser?

Do you have to shim the hanger to lower the tips?


Let me know because I'm ready to order one.

Man, talk about fast shipping. I ordered my flat black diffuser from evor on monday night and now i have a package from taiwan waiting for me at the post office. I will try to install it this weekend and have pictures up.

When i had my FI exhaust I had no issues with the FI exhaust and the diffuser.

Thanks. Only FRP black are in stock. CF is still out.

PM sent!

Memorial Day Special? :tup:

More CF version came in today. All orders are shipped. ONly have 2 CF and 1 FRP black in stock now.

Pmed shipped to canada in CF.

Pm shipped to 92126 San Diego in cf. Can you guys do matte cf? I'm guessing GB is over? Thanks.

Forum member special price is still good. But I'm out of stock on CF version again.